ISL43120IHZ-T(2007) データシートの表示（PDF） - Intersil
部品番号
コンポーネント説明
メーカー
ISL43120IHZ-T Datasheet PDF : 12 Pages
| |||
ISL43120, ISL43121, ISL43122
Absolute Maximum Ratings
V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 15V
Input Voltages
IN (Note 2). . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to ((V+) + 0.3V)
NO, NC (Note 2) . . . . . . . . . . . . . . . . . . . . . -0.3V to ((V+) + 0.3V)
Output Voltages
COM (Note 2) . . . . . . . . . . . . . . . . . . . . . . . -0.3V to ((V+) + 0.3V)
Continuous Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . . 30mA
Peak Current NO, NC, or COM
(Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . . . 40mA
ESD Rating
Human Body Model (Per MIL-STD-883 Method 3015) . . . . .>2kV
Thermal Information
Thermal Resistance (Typical, Note 3)
θJA (°C/W)
8 Ld SOT-23 Package . . . . . . . . . . . . . . . . . . . . . . .
215
Maximum Junction Temperature (Plastic Package). . . . . . . +150°C
Maximum Storage Temperature Range . . . . . . . . . . . -65°C to +150°C
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Operating Conditions
Temperature Range
ISL43XXXIH-T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTES:
2. Signals on NC, NO, COM, or IN exceeding V+ or GND are clamped by internal diodes. Limit forward diode current to maximum current ratings.
3. θJA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications - 5V Supply Test Conditions: V+ = +4.5V to +5.5V, GND = 0V, VINH = 2.4V, VINL = 0.8V (Note 4),
Unless Otherwise Specified.
PARAMETER
TEST CONDITIONS
TEMP
MIN
MAX
(°C) (Notes 5, 6) TYP (Notes 5, 6) UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, VANALOG
ON-Resistance, rON
V+ = 4.5V, ICOM = 1.0mA, VNO or VNC = 3.5V
(See Figure 5)
Full
0
25
-
Full
-
-
V+
V
19
30
Ω
23
40
Ω
rON Matching Between Channels, V+ = 5V, ICOM = 1.0mA, VNO or VNC = 3.5V
ΔrON
25
-
Full
-
rON Flatness, rFLAT(ON)
V+ = 5V, ICOM = 1.0mA, VNO or VNC = 1V, 2V, 3V
Full
-
NO or NC OFF Leakage Current, V+ = 5.5V, VCOM = 1V, 4.5V, VNO or VNC = 4.5V, 1V
25
-0.1
INO(OFF) or INC(OFF)
Full
-5
0.8
1
7
0.01
-
2
Ω
4
Ω
8
Ω
0.1
nA
5
nA
COM OFF Leakage Current,
V+ = 5.5V, VCOM = 4.5V, 1V, VNO or VNC = 1V, 4.5V
25
-0.1
-
0.1
nA
ICOM(OFF)
Full
-5
-
5
nA
COM ON Leakage Current,
V+ = 5.5V, VCOM = 1V, 4.5V, or VNO or VNC = 1V, 4.5V, 25
-0.2
-
0.2
nA
ICOM(ON)
or Floating
Full
-10
-
10
nA
DYNAMIC CHARACTERISTICS
Turn-ON Time, tON
VNO or VNC = 3V, RL =1kΩ, CL = 35pF, VIN = 0V to 3V 25
-
(See Figure 1, Note 7)
Full
-
28
75
ns
40
150
ns
Turn-OFF Time, tOFF
VNO or VNC = 3V, RL =1kΩ, CL = 35pF, VIN = 0V to 3V 25
-
(See Figure 1, Note 7)
Full
-
20
50
ns
30
100
ns
Break-Before-Make Time Delay
RL = 300Ω, CL = 35pF, VNO = VNC = 3V, VIN = 0V to 3V Full
3
10
-
ns
(ISL43122 only), tD
(See Figure 3, Note 7)
Charge Injection, Q
CL = 1.0nF, VG = 0V, RG = 0Ω (See Figure 2, Note 7)
25
-
3
5
pC
OFF Isolation
RL = 50Ω, CL = 5pF, f = 1MHz (See Figure 4)
25
-
76
-
dB
Crosstalk (Channel-to-Channel) RL = 50Ω, CL = 5pF, f = 1MHz (See Figure 6)
25
-
-105
-
dB
Power Supply Rejection Ratio
RL = 50Ω, CL = 5pF, f = 1MHz
25
-
60
-
dB
NO or NC OFF Capacitance, COFF f = 1MHz, VNO or VNC = VCOM = 0V (See Figure 7)
25
-
8
-
pF
COM OFF Capacitance,
CCOM(OFF)
f = 1MHz, VNO or VNC = VCOM = 0V (See Figure 7)
25
-
8
-
pF
3
FN6033.5
October 18, 2007
Share Link: 