MAX187ACPA データシートの表示（PDF） - Maxim Integrated

部品番号

コンポーネント説明

メーカー

MAX187ACPA

+5V, Low-Power, 12-Bit Serial ADCs

Maxim Integrated 

+5V, Low-Power, 12-Bit Serial ADCs

_______________________________________________________________________Pin Description

PIN

DIP

WIDE SO

1

1

2

3

3

6

NAME

VDD

AIN

SHDN

4

8

REF

5

—

GND

—

10

AGND

—

11

DGND

6

12

DOUT

7

15

CS

8

16

SCLK

—

2,4,5,7,9,13,14

N.C.

FUNCTION

Supply voltage, +5V ±5%

Sampling analog input, 0V to VREF range

Three-level shutdown input. Pulling SHDN low shuts the MAX187/MAX189

down to 10µA (max) supply current. Both MAX187 and MAX189 are fully opera-

tional with either SHDN high or floating. For the MAX187, pulling SHDN high

enables the internal reference, and letting SHDN float disables the internal

reference and allows for the use of an external reference.

Reference voltage—sets analog voltage range and functions as a 4.096V output

for the MAX187 with enabled internal reference. REF also serves as a +2.5V to

VDD input for a precision reference for both MAX187 (disabled internal reference)

and MAX189. Bypass with 4.7µF if internal reference is used, and with 0.1µF if an

external reference is applied.

Analog and digital ground

Analog ground

Digital ground

Serial data output. Data changes state at SCLK’s falling edge.

Active-low chip select initiates conversions on the falling edge. When CS is high,

DOUT is high impedance.

Serial clock input. Clocks data out with rates up to 5MHz.

Not internally connected. Connect to AGND for best noise performance.

_______________Detailed Description

Converter Operation

The MAX187/MAX189 use input track/hold (T/H) and

successive approximation register (SAR) circuitry to

convert an analog input signal to a digital 12-bit output.

No external hold capacitor is needed for the T/H.

Figures 3a and 3b show the MAX187/MAX189 in their

simplest configuration. The MAX187/MAX189 convert

input signals in the 0V to VREF range in 10µs, including

T/H acquisition time. The MAX187’s internal reference

is trimmed to 4.096V, while the MAX189 requires an

external reference. Both devices accept external refer-

ence voltages from +2.5V to VDD. The serial interface

requires only three digital lines, SCLK, CS, and DOUT,

and provides easy interface to microprocessors (µPs).

Both converters have two modes: normal and shut-

down. Pulling SHDN low shuts the device down and

reduces supply current to below 10µA, while pulling

SHDN high or leaving it floating puts the device into the

operational mode. A conversion is initiated by CS

falling. The conversion result is available at DOUT in

unipolar serial format. A high bit, signaling the end of

conversion (EOC), followed by the data bits (MSB first),

make up the serial data stream.

The MAX187 operates in one of two states: (1) internal

reference and (2) external reference. Select internal

reference operation by forcing SHDN high, and external

reference operation by floating SHDN.

Analog Input

Figure 4 illustrates the sampling architecture of the

ADC’s analog comparator. The full-scale input voltage

depends on the voltage at REF.

REFERENCE

ZERO

SCALE

FULL

SCALE

Internal Reference

(MAX187 only)

0V

+4.096V

External Reference

0V

VREF

For specified accuracy, the external reference voltage

range spans from +2.5V to VDD.

_______________________________________________________________________________________ 7

Share Link: