LT1956IFE データシートの表示（PDF） - Linear Technology
部品番号
コンポーネント説明
メーカー
LT1956IFE Datasheet PDF : 28 Pages
| |||
LT1956/LT1956-5
ELECTRICAL CHARACTERISTICS
The q denotes specifications which apply over the full operating temperature range, otherwise specifications are at TJ = 25°C.
VIN = 15V, VC = 1.5V, SHDN = 1V, Boost o/c, SW o/c, unless otherwise noted.
PARAMETER
CONDITIONS
MIN TYP MAX
Switch Current Limit
Switch On Resistance
VC Open, Boost = VIN + 5V, FB = 1V or VSENSE = 4.1V q 1.5
2
3
ISW = 1.5A, Boost = VIN + 5V (Note 7)
0.2 0.3
q
0.4
Maximum Switch Duty Cycle
FB = 1V or VSENSE = 4.1V
82 90
q 75 90
Switch Frequency
VC Set to Give DC = 50%
460 500 540
q 430
570
fSW Line Regulation
fSW Shifting Threshold
5.5V ≤ VIN ≤ 60V
Df = 10kHz
q
0.05 0.15
0.8
UNITS
A
Ω
Ω
%
%
kHz
kHz
%/V
V
Minimum Input Voltage
Minimum Boost Voltage
Boost Current (Note 5)
Input Supply Current (IVIN)
Output Supply Current (IBIAS)
Shutdown Supply Current
Lockout Threshold
Shutdown Thresholds
Minimum SYNC Amplitude
SYNC Frequency Range
SYNC Input Resistance
(Note 3)
(Note 4) ISW ≤ 1.5A
Boost = VIN + 5V, ISW = 0.5A
Boost = VIN + 5V, ISW = 1.5A
(Note 6) VBIAS = 5V
(Note 6) VBIAS = 5V
SHDN = 0V, VIN ≤ 60V, SW = 0V, VC Open
VC Open
VC Open, Shutting Down
VC Open, Starting Up
q
4.6 5.5
V
q
2
3
V
q
12 25
mA
q
42 70
mA
1.4 2.2
mA
2.9 4.2
mA
25 75
µA
q
200
µA
q 2.30 2.42 2.53
V
q 0.15 0.37 0.6
V
q 0.25 0.45 0.6
V
q
1.5 2.2
V
580
700
kHz
20
kΩ
Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be impaired.
Note 2: Gain is measured with a VC swing equal to 200mV above the low
clamp level to 200mV below the upper clamp level.
Note 3: Minimum input voltage is not measured directly, but is guaranteed
by other tests. It is defined as the voltage where internal bias lines are still
regulated so that the reference voltage and oscillator remain constant.
Actual minimum input voltage to maintain a regulated output will depend
upon output voltage and load current. See Applications Information.
Note 4: This is the minimum voltage across the boost capacitor needed to
guarantee full saturation of the internal power switch.
Note 5: Boost current is the current flowing into the BOOST pin with the
pin held 5V above input voltage. It flows only during switch on time.
Note 6: Input supply current is the quiescent current drawn by the input
pin when the BIAS pin is held at 5V with switching disabled. Bias supply
current is the current drawn by the BIAS pin when the BIAS pin is held at
5V. Total input referred supply current is calculated by summing input
supply current (IVIN) with a fraction of supply current (IBIAS):
ITOTAL = IVIN + (IBIAS)(VOUT/VIN)
with VIN = 15V, VOUT = 5V, IVIN = 1.4mA, IBIAS = 2.9mA, ITOTAL = 2.4mA.
Note 7: Switch on resistance is calculated by dividing VIN to SW voltage by
the forced current (1.5A). See Typical Performance Characteristics for the
graph of switch voltage at other currents.
Note 8: The LT1956EFE/LT1956EFE-5/LT1956EGN/LT1956EGN-5 are
guaranteed to meet performance specifications from 0°C to 125°C
junction temperature. Specifications over the –40°C to 125°C operating
junction temperature range are assured by design, characterization and
correlation with statistical process controls. The LT1956IFE/LT1956IFE-5/
LT1956IGN/LT1956IGN-5 are guaranteed over the full – 40°C to 125°C
operating junction temperature range.
Note 9: Transconductance and voltage gain refer to the internal amplifier
exclusive of the voltage divider. To calculate gain and transconductance,
refer to the SENSE pin on fixed voltage parts. Divide values shown by the
ratio VOUT/1.219.
Note 10: This IC includes overtemperature protection that is intended to
protect the device during momentary overload conditions. Junction
temperature will exceed 125°C when overtemperature protection is active.
Continuous operation above the specified maximum operating junction
temperature may impair device reliability.
1956f
3
Share Link: 