LTC1657L データシートの表示（PDF） - Linear Technology

部品番号

コンポーネント説明

メーカー

LTC1657L

Parallel 16-Bit Rail-to-Rail Micropower DAC

Linear Technology 

U

OPERATION

Parallel Interface

The data on the input of the DAC is written into the DAC’s

input registers when Chip Select (CSLSB and/or CSMSB)

and WR are at a logic low. The data that is written into the

input registers will depend on which of the Chip Selects

are at a logic low (see Digital Interface Truth Table). If WR

and CSLSB are both low and CSMSB is high, then only

data on the eight LSBs (D0 to D7) is written into the input

registers. Similarly, if WR and CSMSB are both low and

CSLSB is high, then only data on the eight MSBs (D8 to

D15) is written into the input registers. Data is written into

both the Least Significant Data Bits (D0 to D7) and the Most

Significant Bits (D8 to D15) at the same time if WR, CSLSB

and CSMSB are low. If WR is high or both CSMSB and

CSLSB are high, then no data is written into the input

registers.

Once data is written into the input registers, it can be

written into the DAC register. This will update the analog

voltage output of the DAC. The DAC register is written by

a logic low on LDAC. The data in the DAC register will be

held when LDAC is high.

When WR, CSLSB, CSMSB and LDAC are all low, the

registers are transparent and data on pins D0 to D15 flows

directly into the DAC register.

For an 8-bit data bus connection, tie the MSB byte data

pins to their corresponding LSB byte pins (D15 to D7, D14

to D6, etc).

Power-On Reset

The LTC1657L has an internal power-on reset that resets

all internal registers to 0’s on power-up (equivalent to the

CLR pin function).

Reference

The LTC1657L includes an internal 1.25V reference, giv-

ing the LTC1657L a full-scale range of 2.5V in the gain-of-

2 configuration. The onboard reference in the LTC1657L is

not internally connected to the DAC’s reference resistor

string but is provided on an adjacent pin for flexibility.

Because the internal reference is not internally connected

to the DAC resistor ladder, an external reference can be

LTC1657L

used or the resistor ladder can be driven by an external

source in multiplying applications. The external reference

or source must be capable of driving the 16k (minimum)

DAC ladder resistance.

Internal reference output voltage noise spectral density

can be reduced with a bypass capacitor to ground. (Note:

The reference does not require a bypass capacitor to

ground for nominal operation.) When bypassing the refer-

ence, a small value resistor in series with the capacitor is

recommended to help reduce peaking on the output. A

10Ω resistor in series with a 4.7µF capacitor is optimum

for reducing reference generated noise. Internal reference

output noise at 1kHz is typically 80nV/√Hz.

DAC Resistor Ladder

The high and low end of the DAC ladder resistor string

(REFHI and REFLO, respectively) are not connected inter-

nally on this part. Typically, REFHI will be connected to

REFOUT and REFLO will be connected to GND. X1/X2

connected to GND will give the LTC1657L a full-scale

output swing of 2.5V.

Either of these pins can be driven up to VCC – 1.5V when

using the buffer in the gain-of-1 configuration. The resis-

tor string pins can be driven to VCC/2 when the buffer is in

the gain of 2 configuration. The resistance between these

two pins is typically 30k (16k min).

Voltage Output

The output buffer for the LTC1657L can be configured for

two different gain settings. By tying the X1/X2 pin to GND,

the gain is set to 2. By tying the X1/X2 pin to VOUT, the gain

is set to unity.

The LTC1657L rail-to-rail buffered output can source or

sink 5mA to within 500mV of the positive supply voltage

or ground at room temperature. The output stage is

equipped with a deglitcher that results in a midscale glitch

impulse of 8nV • s. The output swings to within a few

millivolts of either supply rail when unloaded and has an

equivalent output resistance of 40Ω when driving a load to

the rails.

7

Share Link: