LX2207ILD データシートの表示（PDF） - Microsemi Corporation
部品番号
コンポーネント説明
メーカー
LX2207ILD Datasheet PDF : 14 Pages
| |||
LX2207
Three Level Lithium Ion Battery Charger
®
TM
PRODUCTION DATA SHEET
ABSOLUTE MAXIMUM RATINGS
PACKAGE PIN OUT
Supply Input Voltage (IN, BAT) ...................................................................... -0.3V to 7V
All other pins ............................................................................................-0.3V to VSUPPLY
Battery Charging Current .............................................................................................1.1A
Operating Temperature Range .........................................................................-40 to 150°C
Maximum Operating Junction Temperature .............................................................. 150°C
Storage Temperature Range.........................................................................-65°C to 150°C
Peak Temp. for Solder Reflow (40 seconds maximum exposure).................. 260°C (+0 -5)
Note: Exceeding these ratings could cause damage to the device. All voltages are with respect to
Ground. Currents are positive into, negative out of specified terminal.
THERMAL DATA
IN
1
CMP
2
STAT 3
DCOK 4
SD
5
20%
6
12
BAT
11
TMP
10
HCP
9 LCP
8 H/L
7 GND
LD Package
(Top View)
RoHS / Pb-free 100% matte Tin Finish
LD Plastic Micro Leadframe Package 12-Pin
THERMAL RESISTANCE-JUNCTION TO AMBIENT, θJA
33°C/W
Junction Temperature Calculation: TJ = TA + (PD x θJA).
The θJA numbers are guidelines for the thermal performance of the device/pc-board system. All of the
above assume no ambient airflow.
Part Marking
xxxx = Denotes date and
lot code Identification
Name
BAT
CMP
DCOK
GND
HCP
H/ L
IN
LCP
SD
STAT
TMP
20%
Pin #
12
2
4
7
10
8
1
9
5
3
11
6
FUNCTIONAL PIN DESCRIPTION
Description
Battery – Connect to a single cell Lithium Ion Battery.
Compensation – Connect a series combination of a 1k resistor and a 0.47µF capacitor from CMP to IN.
Power status logic pin and LED driver – This pin is an open drain output that can sink 20mA of current to
drive an external LED. This pin is low impedance to GND when the Input voltage is high enough to charge
the Battery.
Ground – Connect to the system ground.
High Current Programming (and Termination Current Programming) – Connect a resistor to ground to set the
constant current high level. The termination current is set to 1/10 of the High Current Programming Level.
For a value of 19.6k, the High Current is 460mA and the Termination Current is 46mA.
High or Low load select logic input – A logic high selects the constant charge current level set by the HCP pin
resistor and a logic low selects the constant charge current level set by the LCP pin resistor
Input Power – Connect to a wall adapter or a USB power plug.
Low Current Programming – Connect a resistor to ground to set the constant current low level.
For a value of 19.6k, the High Current is 460mA and the 20% current is 92mA.
Shutdown – A logic high places the LX2207 in sleep mode; can also be used for USB suspend.
Charging status logic pin and LED driver – This pin can source or sink 10mA of current to drive an external
LED in either output state. This pin is low (current sinking mode) when the battery is in charging mode and
becomes high (current sourcing mode) when the charge cycle is finished. It becomes high impedance when
the input power is removed.
Battery Temperature Monitor – This sense pin determines the battery temperature for charging out of
temperature range lockout and is connected to a resistor network as defined in the Applications section. The
TMP pin is grounded if this function is not used.
20% select logic input – When the low current level is selected by the H/L pin, a logic high on 20% selects the
constant charge current level set by the LCP pin resistor and a logic low selects 20% of this value.
Copyright © 2007
Rev. 1.0a, 2007-10-08
Microsemi
Analog Mixed Signal Group
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 2
Share Link: 