MACH211SP-10 データシートの表示（PDF） - Advanced Micro Devices

部品番号

コンポーネント説明

メーカー

MACH211SP-10

High-Density EE CMOS Programmable Logic

Advanced Micro Devices 

ABSOLUTE MAXIMUM RATINGS

Storage Temperature . . . . . . . . . . . . –65°C to +150°C

Ambient Temperature

with Power Applied. . . . . . . . . . . . . . –55°C to +125°C

Supply Voltage with

Respect to Ground. . . . . . . . . . . . . . . –0.5 V to +7.0 V

DC Input Voltage . . . . . . . . . . . .–0.5 V to VCC + 0.5 V

DC Output or

I/O Pin Voltage . . . . . . . . . . . . . .–0.5 V to VCC + 0.5 V

Static Discharge Voltage . . . . . . . . . . . . . . . . . 2001 V

Latchup Current (TA = 0°C to 70°C) . . . . . . . . 200 mA

Stresses above those listed under Absolute Maximum

Ratings may cause permanent device failure. Functionality at

or above these limits is not implied. Exposure to Absolute

Maximum Ratings for extended periods may affect device

reliability. Programming conditions may differ.

OPERATING RANGES

Commercial (C) Devices

Ambient Temperature (TA)

Operating in Free Air. . . . . . . . . . . . . . . .0°C to +70°C

Supply Voltage (VCC)

with Respect to Ground . . . . . . . . +4.75 V to +5.25 V

Operating ranges define those limits between which the

functionality of the device is guaranteed.

DC CHARACTERISTICS over COMMERCIAL operating ranges unless otherwise specified

Parameter

Symbol

Parameter Description

Test Conditions

Min Typ Max Unit

VOH

Output HIGH Voltage

VOL

Output LOW Voltage

VIH

Input HIGH Voltage

IOH = –3.2 mA, VCC = Min, VIN = VIH or VIL 2.4

IOL = 16 mA, VCC = Min, VIN = VIH or VIL

Guaranteed Input Logical HIGH

Voltage for all Inputs (Note 1)

2.0

V

0.5

V

V

VIL

Input LOW Voltage

Guaranteed Input Logical LOW

Voltage for all Inputs (Note 1)

0.8

V

IIH

IIL

IOZH

IOZL

ISC

ICC

Input HIGH Current

Input LOW Current

Off-State Output Leakage

Current HIGH

Off-State Output Leakage

Current LOW

Output Short-Circuit Current

Supply Current (Static)

Supply Current (Active)

VIN = 5.25 V, VCC = Max (Note 2)

VIN = 0 V, VCC = Max (Note 2)

VOUT = 5.25 V, VCC = Max

VIN = VIH or VIL (Note 2)

VOUT = 0 V, VCC = Max

VIN = VIH or VIL (Note 2)

VOUT = 0.5 V, VCC = Max (Notes 3, 5)

–30

VCC = 5 V, TA = 25°C, f = 0 MHz (Note 4)

VCC = 5 V, TA = 25°C, f = 1 MHz (Note 4)

10

µA

–10 µA

10

µA

–10

µA

–160 mA

40

mA

45

mA

Notes:

1. These are absolute values with respect to device ground and all overshoots due to system and/or tester noise are included.

2. I/O pin leakage is the worst case of IIL and IOZL (or IIH and IOZH).

3. Not more than one output should be shorted at a time. Duration of the short-circuit should not exceed one second.

VOUT = 0.5 V has been chosen to avoid test problems caused by tester ground degradation.

4. This parameter is measured in low-power mode with a 16-bit up/down counter pattern. This pattern is programmed in each

PAL block and is capable of being loaded, enabled and reset.

5. This parameter is not 100% tested, but is evaluated at initial characterization and at any time the design is modified where

capacitance may be affected.

10

MACH211SP-7/10 (Com’l)

Share Link: