MASW-007073-000100
GaAs SP4T Absorptive Switch with
ASIC Driver, DC-3.0 GHz
Rev. V4
Electrical Specifications: TA = 25°C, Z0 = 50Ω
Parameter
Test Conditions
Insertion Loss
DC - 1.0 GHz
DC - 2.0 GHz
DC - 3.0 GHz
Isolation
(One Arm On)
DC - 1.0 GHz
DC - 2.0 GHz
DC - 3.0 GHz
VSWR
Trise Tfall
Ton
Toff
Transients
DC - 1.0 GHz
DC - 2.0 GHz
DC - 3.0 GHz
10%/90%, 90%/10% 1
50% TTL to 90%/10% RF
In-band (peak to peak)
1 dB Compression
.05 GHz
.5 - 3.0 GHz
Input IP3
Two tone inputs 0.05 GHz
Up to +5 dBm 0.5 - 3.0 GHz
VCC
—
Units
dB
dB
dB
dB
dB
dB
—
—
—
ns
ns
mV
dBm
dBm
dBm
dBm
V
Min
—
—
—
35
27
25
—
—
—
—
—
—
—
—
—
—
+4.5
Typ
1.5
1.6
2.0
38
33
27
On
1.3:1
1.5:1
1.7:1
Off
1.3:1
1.7:1
2.2:1
15
50
50
+20
+27
+35
+46
+5.0
Max
1.7
1.8
2.3
—
—
—
1.5:1
2.0:1
2.4:1
50
150
150
—
—
—
—
+5.5
VEE
—
V
-8.0
-5.0
-4.75
VIL
LOW-level input voltage
V
0.0
—
0.8
VIH
HIGH-level input voltage
V
2.0
—
5.0
lin (Input Leakage Current)
Vin = VCC or GND
uA
-1.0
—
1.0
ICC
(Quiescent Supply Current)
Vcntrl = VCC or GND
uA
—
250
400
ΔICC
(Additional Supply Current Per
TTL Input Pin)
VCC = Max, Vcntrl = VCC - 2.1V
mA
—
—
1.0
IEE
VEE min to max, Vin = VIL or VIH
mA
-1.0
-0.2
—
1. Decoupling capacitors (.01 µF) are required on the power supply lines. Handling Procedures
Absolute Maximum Ratings 2,3
Please observe the following precautions to avoid
damage:
Parameter
Absolute Maximum
Static Sensitivity
Max. Input Power
0.05 GHz
0.5 - 3.0 GHz4
VCC
VEE
+27 dBm
+34 dBm
-0.5V ≤ VCC ≤ +7.0V
-8.5V ≤ VEE ≤ +0.5V
Gallium Arsenide Integrated Circuits are sensitive
to electrostatic discharge (ESD) and can be
damaged by static electricity. Proper ESD control
techniques should be used when handling these
devices.
VCC - VEE
Vin5
Operating Temperature
Storage Temperature
-0.5V ≤ VCC - VEE ≤ 14.5V
-0.5V ≤ Vin ≤ VCC + 0.5V
-40ºC to +85ºC
-65ºC to +125ºC
2. Exceeding any one or combination of these limits may cause
permanent damage to this device.
3. M/A-COM does not recommend sustained operation near
these survivability limits.
4. When the RF input is applied to the terminated port, the
absolute maximum power is +30 dBm.
5. Standard CMOS TTL interface, latch-up will occur if logic
signal is applied prior to power supply.
2
ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 • Europe Tel: +353.21.244.6400
is considering for development. Performance is based on target specifications, simulated results,
and/or prototype measurements. Commitment to develop is not guaranteed.
PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology
• India Tel: +91.80.4155721
• China Tel: +86.21.2407.1588
Visit www.macomtech.com for additional data sheets and product information.
Solutions has under development. Performance is based on engineering tests. Specifications are
typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make
Commitment to produce in volume is not guaranteed.
changes to the product(s) or information contained herein without notice.