MAX4509CSE(2007) データシートの表示（PDF） - Maxim Integrated

部品番号

コンポーネント説明

メーカー

MAX4509CSE
(Rev.:2007)

Fault-Protected, High-Voltage Single 8-to-1/Dual 4-to-1 Multiplexers with Output Clamps

Maxim Integrated 

Fault-Protected, High-Voltage Single 8-to-1/

Dual 4-to-1 Multiplexers with Output Clamps

ABSOLUTE MAXIMUM RATINGS

(Voltages Referenced to GND)

V+ ........................................................................-0.3V to +44.0V

V- .........................................................................-44.0V to +0.3V

V+ to V-................................................................-0.3V to +44.0V

COM_, A_ (Note 1) .............................. (V+ + 0.3V) to (V- - 0.3V)

NO_.........................................................(V+ - 40V) to (V- + 40V)

NO_ to COM_ ..........................................................-36V to +36V

NO_ Overvoltage with Switch Power On. ................-30V to +30V

NO_ Overvoltage with Switch Power Off. ................-40V to +40V

Continuous Current into Any Terminal..............................±30mA

Peak Current, into Any Terminal

(pulsed at 1ms, 10% duty cycle).................................±100mA

Continuous Power Dissipation (TA = +70°C)

16 Narrow SO (derate 8.70mW/°C above +70°C) ........696mW

16-Pin PDIP (derate 10.53mW/°C above +70°C)..........842mW

16-Pin CERDIP (derate 10.00mW/°C above +70°C).....800mW

Operating Temperature Ranges

MAX4508C_ E/MAX4509C_E...............................0°C to +70°C

MAX4508E_ E/MAX4509E_E ............................-40°C to +85°C

MAX4508MJE/MAX4509MJE..........................-55°C to +125°C

Storage Temperature Range .............................-65°C to +160°C

Lead Temperature (soldering, 10s) .................................+300°C

Note 1: COM_, EN, and A_ pins are not fault protected. Signals on COM_, EN, or A_ exceeding V+ or V- are clamped by internal

diodes. Limit forward diode current to maximum current rating.

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional

operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to

absolute maximum rating conditions for extended periods may affect device reliability.

ELECTRICAL CHARACTERISTICS—Dual Supplies

(V+ = +15V, V- = -15V, VA_H =+2.4V, VA_L = +0.8V, VEN = +2.4V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at

TA = +25°C.) (Note 2)

PARAMETER

SYMBOL

CONDITIONS

TA

MIN TYP MAX UNITS

ANALOG SWITCH

Fault-Free Analog Signal Range

(Notes 3, 4)

VNO_

V+ = +15V, V- = -15V,

VNO_= ±15V

On-Resistance

RON VCOM_ = ±10V, INO_ = 0.2mA

C, E, M

V-

V+

V

+25°C

C, E

M

300

400

500

Ω

700

On-Resistance Match Between

Channels (Note 5)

ΔRON VCOM_ = ±10V, INO_ = 0.2mA

NO_ Off-Leakage Current

(Note 6)

INO_(OFF) VNO_ = ±10V, VCOM_ = +– 10V

+25°C

C, E

M

+25°C

-0.5

C, E

-5

M

-50

15

20

Ω

25

+0.5

+5

nA

+50

+25°C

-2

+2

MAX4508

C, E

-20

+75

COM_ Off-Leakage Current

(Note 6)

ICOM_(OFF)

VCOM_ = ±10V,

VNO_ = +– 10V

M

+25°C

-200

-1

+200

nA

+1

MAX4509

C, E

-100

+75

M

-100

+100

+25°C

-2

+2

COM_ On-Leakage Current

(Note 6)

VCOM_ = ±10V,

ICOM_(ON) VNO_ = ±10V or

floating

MAX4508

MAX4509

C, E

M

+25°C

C, E

-100

-300

-1

-15

+75

+300

nA

+1

+75

M

-150

+150

2 _______________________________________________________________________________________

Share Link: