MAX4711CSE データシートの表示（PDF） - Maxim Integrated
部品番号
コンポーネント説明
メーカー
MAX4711CSE Datasheet PDF : 17 Pages
| |||
Fault-Protected, Low-Voltage,
Quad SPST Analog Switches
ABSOLUTE MAXIMUM RATINGS
V+ ...........................................................................-0.3V to +13V
V- ............................................................................-13V to +0.3V
V+ to V-...................................................................-0.3V to +13V
IN_...........................................................(V- + 12V) to (V- - 0.3V)
COM_ (Note 1)......................................(V- - 0.3V) to (V+ + 0.3V)
NO_, NC_ (Note 2)..................................(V+ - 12V) to (V- + 12V)
Continuous Current into Any Terminal..............................±40mA
Peak Current, into Any Terminal
(pulsed at 1ms,10% duty cycle).................................±70mA
Continuous Power Dissipation (TA = +70°C)
16-Pin TSSOP (derate 5.70mW/°C above +70°C) ...........457mW
16-Pin Narrow SO (derate 8.70mW/°C above +70°C).....696mW
16-Pin Plastic Dip (derate 10.53mW/°C above +70°C) ...842mW
Operating Temperature Ranges
MAX471_C_ E .....................................................0°C to +70°C
MAX471_E_ E ..................................................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Note 1: COM_ pin is not fault-protected. Signals on COM_ exceeding V+ or V- are clamped by internal diodes. Limit forward diode
current to maximum current rating.
Note 2: NO_ and NC_ pins are fault-protected. Signals on NO_ or NC_ exceeding -12V to +12V may damage device. These limits
apply with V+ = V- = 0.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS—Dual Supplies
(V+ = +4.5V to +5.5V, V- = -4.5V to -5.5V, VIH = +2.4V, VIL = +0.8V, GND = 0, TA = TMIN to TMAX, unless otherwise noted. Typical
values are at TA = +25°C.) (Note 3)
PARAMETER
ANALOG SWITCH
SYMBOL
CONDITIONS
TA
MIN TYP MAX UNITS
Fault-Free Analog Signal Range VCOM_, Applies with power on
VNO_,VNO_
C, E
V-
V+
V
On-Resistance
RON
V+ = +4.5V, V- = -4.5V,
VNO_, VNC_ = ±3.5V, IOUT = 10mA
+25°C
C, E
16
25
Ω
30
On-Resistance Match Between
Channels (Note 4)
∆RON
V+ = +4.5V, V- = -4.5V,
VNO_, VNC_ = ±3.5V, IOUT = 10mA
+25°C
C, E
0.2
1
Ω
2
On-Resistance Flatness
RFLAT
V+ = +4.5V, V- = -4.5V,
VNO_, VNC_ = ±3.5V, IOUT = 10mA
+25°C
C, E
1.3
4
Ω
5
NO_, NC_ Off-Leakage Current
(Note 5)
INO_(OFF),
INC_(OFF)
V+ = +5.5V, V- = -5.5V,
VCOM_ = ±4.5V,
VNO_, VNC_ = 4.5V
+25°C
-0.5
C, E
-10
+0.5
nA
+10
COM_ Off-Leakage Current
(Note 5)
COM_ On-Leakage Current
(Note 5)
FAULT
ICOM_(OFF)
V+ = +5.5V, V- = -5.5V,
VCOM_ = ±4.5V,
VNO_, VNC_ = 4.5V
+25°C
-0.5
C, E
-10
V+ = +5.5V, V- = -5.5V,
+25°C
-0.5
ICOM_(ON) VCOM_ = ±4.5V,
VNO_, VNC_ = ±4.5V or floating
C, E
-20
+0.5
nA
+10
+0.5
nA
+20
Fault-Protected Analog Signal
Range
VNO_,
VNC_
Applies with power on
C, E -12 + V+
+12 + V- V
Fault-Protected Analog Signal
Range
VNO_,
VNC_
Applies with power off
C, E
-12
+12
V
COM_ Output-Leakage Current,
Supplies ON (Note 5)
ICOM
All channels off,
V+ = +5V, V- = -5V,
VNO_, VNC_ = ±7V
+25°C
C, E
-50
-500
+50
nA
+500
2 _______________________________________________________________________________________
Share Link: 