MC100LVEP210 データシートの表示（PDF） - ON Semiconductor
部品番号
コンポーネント説明
メーカー
MC100LVEP210 Datasheet PDF : 9 Pages
| |||
MC100LVEP210
Table 3. MAXIMUM RATINGS
Symbol
Parameter
Condition 1
Condition 2
Rating
Unit
VCC
PECL Mode Power Supply
VEE
NECL Mode Power Supply
VI
PECL Mode Input Voltage
NECL Mode Input Voltage
Iout
Output Current
VEE = 0 V
VCC = 0 V
VEE = 0 V
VCC = 0 V
Continuous
Surge
VI ≤ VCC
VI ≥ VEE
6
V
−6
V
6
V
−6
V
50
mA
100
mA
IBB
VBB Sink/Source
TA
Operating Temperature Range
Tstg
Storage Temperature Range
qJA
Thermal Resistance (Junction−to−Ambient) 0 lfpm
500 lfpm
LQFP−32
LQFP−32
± 0.5
−40 to +85
−65 to +150
80
55
mA
°C
°C
°C/W
°C/W
qJC
Thermal Resistance (Junction−to−Case)
Standard Board
LQFP−32
12 to 17
°C/W
Tsol
Wave Solder
Pb <2 to 3 sec @ 248°C
Pb−Free <2 to 3 sec @ 260°C
265
°C
265
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
Table 4. PECL DC CHARACTERISTICS VCC = 2.5 V; VEE = 0 V (Note 2)
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
VOH
VOL
VIHCMR
Power Supply Current
Output HIGH Voltage (Note 3)
Output LOW Voltage (Note 3)
Input HIGH Voltage Common Mode
Range (Differential Configuration)
(Note 4)
55
70
90
55
70
90
55
70
90
mA
1355 1480 1605 1355 1480 1605 1355 1480 1605 mV
555 680 900 555 680 900 555 680 900 mV
1.2
2.5 1.2
2.5 1.2
2.5
V
VIL
Input LOW Voltage (Single−Ended)
555
IIH
Input HIGH Current
IIL
Input LOW Current
CLK 0.5
CLK −150
900 555
150
0.5
−150
900 555
150
0.5
−150
900 mV
150 mA
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
2. Input and output parameters vary 1:1 with VCC. VEE can vary + 0.125 V to −1.3 V.
3. All loading with 50 W to VEE.
4. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal.
http://onsemi.com
3
Share Link: 