MC100EP142FAG(2015) データシートの表示（PDF） - ON Semiconductor
部品番号
コンポーネント説明
メーカー
MC100EP142FAG Datasheet PDF : 14 Pages
| |||
MC10EP142, MC100EP142
Table 9. 100EP DC CHARACTERISTICS, PECL VCC = 5.0 V, VEE = 0 V (Note 18)
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
VIHCMR
IIH
IIL
Input HIGH Voltage Common Mode
2.0
Range (Differential Configuration)
(Note 21)
Input HIGH Current (@ VIH)
Input LOW Current (@ VIL)
CLK0, CLK1, D, S−IN
CLK0, CLK1, S−IN
0.5
−150
5.0 2.0
150
0.5
−150
5.0 2.0
150
0.5
−150
5.0
V
150 mA
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm.
18. Input and output parameters vary 1:1 with VCC. VEE can vary +2.0 V to −0.5 V.
19. Required 500 lfpm air flow when using +5 V power supply. For (VCC − VEE) >3.3 V, 5 W to 10 W in line with VEE required for maximum thermal
protection at elevated temperatures. Recommend VCC−VEE operation at 3.3 V.
20. All loading with 50 W to VCC − 2.0 V.
21. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal.
Table 10. 100EP DC CHARACTERISTICS, NECL VCC = 0 V, VEE = −5.5 V to −3.0 V (Note 22)
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
Negative Power Supply Current
105 125 145 105 130 150 105 130 150 mA
(Note 23)
VOH
VOL
VIH
VIL
VIHCMR
IIH
IIL
Output HIGH Voltage (Note 24)
−1145 −1020 −895 −1145 −1020 −895 −1145 −1020 −895 mV
Output LOW Voltage (Note 24)
−1995 −1820 −1695 −1995 −1820 −1695 −1995 −1820 −1695 mV
Input HIGH Voltage (Single−Ended) −1225
−880 −1225
−880 −1225
−880 mV
Input LOW Voltage (Single−Ended) −1995
−1625 −1995
−1625 −1995
−1625 mV
Input HIGH Voltage Common Mode
VEE+2.0
0.0
VEE+2.0
0.0
VEE+2.0
0.0
V
Range (Differential Configuration)
(Note 25)
Input HIGH Current (@ VIH)
Input LOW Current (@ VIL)
CLK0, CLK1, D, S−IN
CLK0, CLK1, S−IN
0.5
−150
150
0.5
−150
150
0.5
−150
150 mA
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm.
22. Input and output parameters vary 1:1 with VCC.
23. Required 500 lfpm air flow when using −5 V power supply. For (VCC − VEE) >3.3 V, 5 W to 10 W in line with VEE required for maximum thermal
protection at elevated temperatures. Recommend VCC−VEE operation at 3.3 V.
24. All loading with 50 W to VCC − 2.0 V.
25. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal.
Table 11. AC CHARACTERISTICS VCC = 3.0 V to 5.5 V; VEE = 0.0 V or VCC = 0.0 V; VEE = −3.0 V to −5.5 V (Note 26)
−40°C
25°C
85°C
Symbol
fSHIFT
tPLH,
tPHL
Characteristic
Maximum Shift Frequency
Propagation Delay to Output
Min Typ Max Min Typ Max Min Typ Max
2.8
CLKx 500 625 750 550 675 800 575 700 825
MR 500 625 750 550 675 800 575 700 825
ts
Setup Time
D 50 −50
SEL 100 50
50 −50
100 50
50 −50
100 50
Unit
GHz
ps
ps
www.onsemi.com
9
Share Link: 