MC100EP142FA データシートの表示（PDF） - ON Semiconductor
部品番号
コンポーネント説明
メーカー
MC100EP142FA Datasheet PDF : 13 Pages
| |||
MC10EP142, MC100EP142
Table 7. 10EP DC CHARACTERISTICS, NECL VCC = 0 V, VEE = −5.5 V to −3.0 V (Note 11)
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
Negative Power Supply Current
105 125 145 105 125 145 105 125 145 mA
(Note 12)
VOH
VOL
VIH
VIL
VIHCMR
Output HIGH Voltage (Note 13)
−1135 −1010 −885 −1070 −945 −820 −1010 −885 −760 mV
Output LOW Voltage (Note 13)
−1935 −1810 −1685 −1870 −1745 −1620 −1810 −1685 −1560 mV
Input HIGH Voltage (Single−Ended) −1210
−885 −1145
−820 −1085
−760 mV
Input LOW Voltage (Single−Ended) −1935
−1610 −1870
−1545 −1810
−1485 mV
Input HIGH Voltage Common Mode
VEE+2.0
0.0
VEE+2.0
0.0
VEE+2.0
0.0
V
Range (Differential Configuration)
(Note 14)
IIH
Input HIGH Current (@ VIH)
IIL
Input LOW Current (@ VIL)
CLK0, CLK1, D, S−IN 0.5
CLK0, CLK1, S−IN −150
150
0.5
−150
150
0.5
−150
150 mA
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
11. Input and output parameters vary 1:1 with VCC.
12. Required 500 lfpm air flow when using −5 V power supply. For (VCC − VEE) >3.3 V, 5 W to 10 W in line with VEE required for maximum thermal
protection at elevated temperatures. Recommend VCC−VEE operation at 3.3 V.
13. All loading with 50 W to VCC − 2.0 V.
14. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal.
Table 8. 100EP DC CHARACTERISTICS, PECL VCC = 3.3 V, VEE = 0 V (Note 15)
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
VOH
VOL
VIH
VIL
VIHCMR
Negative Power Supply Current
Output HIGH Voltage (Note 16)
Output LOW Voltage (Note 16)
Input HIGH Voltage (Single−Ended)
Input LOW Voltage (Single−Ended)
Input HIGH Voltage Common Mode
Range (Differential Configuration)
(Note 17)
105 125 145 105 130 150 105 130 150 mA
2155 2280 2405 2155 2280 2405 2155 2280 2405 mV
1355 1480 1605 1355 1480 1605 1355 1480 1605 mV
2075
2420 2075
2420 2075
2420 mV
1355
1675 1355
1675 1355
1675 mV
2.0
3.3 2.0
3.3 2.0
3.3
V
IIH
Input HIGH Current (@ VIH)
IIL
Input LOW Current (@ VIL)
CLK0, CLK1, D, S−IN 0.5
CLK0, CLK1, S−IN −150
150
0.5
−150
150
0.5
−150
150 mA
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
15. Input and output parameters vary 1:1 with VCC. VEE can vary +0.3 V to −2.2 V.
16. All loading with 50 W to VCC − 2.0 V.
17. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal.
http://onsemi.com
7
Share Link: 