MCR106 データシートの表示（PDF） - Unisonic Technologies
部品番号
コンポーネント説明
メーカー
MCR106 Datasheet PDF : 3 Pages
| |||
MCR106
SCR
ABSOLUTE MAXIMUM RATINGS (TJ=25℃, unless otherwise specified)
PARAMETER
SYMBOL
RATINGS
UNIT
Peak Repetitive Forward and Reverse Blocking MCR106-6
400
V
Voltage (Note 1) (TJ=110℃, RGK=1kΩ)
MCR106-8
VDRM, VRRM
600
V
RMS Forward Current (All conduction Angles)
Average Forward Current (TC=93℃ or TA=30℃)
Peak Non-repetitive Surge Current
(1/2 Cycle, 60Hz, TJ=-40 ~ +110℃)
Circuit Fusing Considerations (t=8.3 ms)
IT(RMS)
IT(AV)
ITSM
I2t
4
2.55
25
2.6
A
A
A
A2S
Peak Gate Power
PGM
0.5
W
Average Gate Power
PG(AV)
0.1
W
Peak Forward Gate Current
IGM
0.2
A
Peak Reversed Gate Voltage
VRGM
6
V
Mounting Torque (Note 2)
6
In. lb.
Junction Temperature
Storage Temperature
TJ
+110
℃
TSTG
-40 ~ +150
℃
Note 1. VDRM and VRRM for all types can be applied on a continuous basis. Ratings apply for zero or negative gate
voltage; however, positive gate voltage shall not be applied concurrent with negative potential on the anode.
Blocking voltages shall not be tested with a constant current source such that the voltage of the devices are
exceeded.
2. Torque rating applies with use of compression washer (B52200-F006 or equivalent). Mounting torque in
excess of 6 in. lb. does not appreciably lower case-to-sink thermal resistance. Anode lead and heatsink
contact pad are common. For soldering purposes (either terminal connection or device mounting), soldering
temperatures shall not exceed +200℃. For optimum results, an activated flux (oxide removing) is
recommended.
3. Absolute maximum ratings are those values beyond which the device could be permanently damaged.
Absolute maximum ratings are stress ratings only and functional device operation is not implied.
THERMAL DATA
Junction to Ambient
Junction to Case
PARAMETER
SYMBOL
θJA
θJC
RATINGS
75
3
UNIT
℃/W
℃/W
ELECTRICAL CHARACTERISTICS (TC=25℃ and RGK=1000 Ω, unless otherwise specified)
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
Peak Forward or Reverse Blocking
TJ=25℃
Current (VAK=Rated VDRM or VRRM)
IDRM,IRRM TJ=100℃
Forward “On” Voltage (ITM=4A peak)
VTM
Gate Trigger Current (continuous DC)
(Note)
Gate Trigger Voltage (continuous DC)
Gate Non-Trigger Voltage
Holding Current
Forward Voltage Application Rate
IGT
VGT
VGD
IH
dv/dt
VAK=7V, RL=100Ω
VAK=7V, RL=100Ω, TC=-40℃
VAK=7V, RL=100Ω, TC=25℃
VAK=Rated VDRM, RL=100Ω, TJ=110℃ 0.2
VAK=7V, TC=25 ℃
TJ=110℃
Note: RGK current is not included in measurement.
TYP
10
MAX UNIT
10 μA
200 μA
2V
200 μA
500
1V
V
5 mA
V/μs
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
2 of 3
QW-R301-001.C
Share Link: 