MICRF003 データシートの表示（PDF） - Micrel

部品番号

コンポーネント説明

メーカー

MICRF003

QwikRadio™ 900 MHz UHF Receiver

Micrel 

MICRF003

QwikRadio tm

Micrel

1. Selecting REFOSC Frequency Ft (FIXED Mode)

As with any superheterodyne receiver, the difference

between the (internal) Local Oscillator (LO) frequency Flo

and the incoming Transmit frequency Ftx must ideally equal

the IF Center frequency. Equation (1) may be used to

compute the appropriate Flo for a given Ftx:

Flo = Ftx ± 2.496 * (Ftx / 915)

(1)

where Ftx and Flo are in MHz. Note that two values of Flo

exist for any given Ftx, distinguished as “high-side mixing”

and “low-side mixing”, and there is generally no preference

of one over the other.

After choosing one of the two acceptable values of Flo, use

equation (2) to compute the REFOSC frequency Ft:

Ft = Flo / 129.

(2)

Here Ft is in MHz. Connect a crystal of frequency Ft to the

REFOSC pin of the MICRF003. 4 decimal-place accuracy

on the frequency is generally adequate. The following table

identifies Ft for some common Transmit frequencies when

the MICRF003 is operated in FIXED mode.

Transmit Freq. Ftx (MHz)

REFOSC Freq. Ft (MHz)

868

6.7470

915

7.1124

2. Selecting REFOSC Frequency Ft (SWP Mode)

Selection of REFOSC frequency Ft in SWP mode is much

simpler than in FIXED mode, due to the LO sweeping

process. Further, accuracy requirements of the frequency

reference component are significantly relaxed.

In SWP mode, Ft is given by equation (3):

Ft = Ftx / 128.5.

(3)

Connect a ceramic resonator of frequency Ft to the

REFOSC pin of the MICRF003. 2-decimal place accuracy

is generally adequate. (A crystal may also be used if

desired, but may be necessary to reduce the Rx frequency

ambiguity if the Tx frequency ambiguity is excessive. See

Application Note TBD for further details.)

3. Selecting Capacitor CTH

Source impedance of the CTH pin is given by equation (4),

where Ft is in MHz:

Rs = 90kΩ * (6.75 / Ft).

(4)

Assuming that a Slicing Level Timeconstant TC has been

established, capacitor CTH may be computed using

equation (5):

CTH = TC / Rs.

(5)

4. Selecting CAGC Capacitor in Continuous Mode

Selection of CAGC in continuous mode is dictated by

minimizing the ripple on the AGC control voltage, by using a

sufficiently large capacitor. It is Micrel’s experience that

CAGC should be in the vicinity of 0.47µF to 4.7µF. Large

capacitor values should be carefully considered, as this

determines the time required for the AGC control voltage to

settle from a completely discharged condition. AGC settling

time from a completely discharged (0-volt) state is given

approximately by equation (6):

∆T = (1.333 * CAGC) – 0.44

(6)

where CAGC is in microfarads, and ∆T is in seconds.

5. Selecting CAGC Capacitor in Duty-Cycle Mode

Generally, droop of the AGC control voltage during

shutdown should be replenished as quickly as possible after

the IC is “turned-on”. Recall from the section “AGC

Function and the CAGC Capacitor” that for about 10msec

after the IC is turned-on, the AGC push-pull currents are

increased to 45X their normal values. So consideration

should be given to selecting a value for CAGC and a

shutdown time period such that the droop can be

replenished within this 10msec period.

Polarity of the droop is unknown, meaning the AGC voltage

could droop up or down. Worst-case from a recovery

standpoint is downward droop, since the AGC pullup current

is 1/10th magnitude of the pulldown current. The downward

droop is replenished according the the well-known equation

(7):

I / CAGC = ∆V / ∆T

(7)

where I = AGC Pullup current for initial 10msec (67.5µA),

CAGC is the AGC capacitor value, ∆T = Droop recovery

time (<10msec), and ∆V is the droop voltage.

First step in the process is selection of a Data Slicing Level

timeconstant. This selection is strongly dependent on

system issues, like system decode response time and data

code structure (e.g., existance of data preamble, etc.). This

issue is too broad to discuss here, and the interested reader

should consult the Application Note TBD.

For example, if user desires ∆T = 10msec, and chooses a

4.7µF CAGC, then the allowable droop is about 144mV.

Using the same equation with 200nA worst case pin

leakage and assuming 1uA of capacitor leakage in the

same direction, the maximum allowable ∆T (Shutdown

time) is about 0.56 seconds, for droop recovery in 10msec.

October 1999

10

MICRF003

Share Link: