AM29F800BT-90SCB データシートの表示（PDF） - Advanced Micro Devices
部品番号
コンポーネント説明
メーカー
AM29F800BT-90SCB
Advanced Micro Devices
AM29F800BT-90SCB Datasheet PDF : 39 Pages
| |||
PRELIMINARY
Table 3. Am29F800BB Bottom Boot Block Sector Address Table
Sector A18 A17 A16 A15 A14 A13 A12
Sector Size
(Kbytes/
Kwords)
Address Range (in hexadecimal)
(x16)
Address Range
(x8)
Address Range
SA0
0
0
0
0
0
0
X
16/8
00000h–01FFFh 00000h–03FFFh
SA1
0
0
0
0
0
1
0
8/4
02000h–02FFFh 04000h–05FFFh
SA2
0
0
0
0
0
1
1
8/4
03000h–03FFFh 06000h–07FFFh
SA3
0
0
0
0
1
X
X
32/16
04000h–07FFFh 08000h–0FFFFh
SA4
0
0
0
1
X
X
X
64/32
08000h–0FFFFh 10000h–1FFFFh
SA5
0
0
1
0
X
X
X
64/32
10000h–17FFFh 20000h–2FFFFh
SA6
0
0
1
1
X
X
X
64/32
18000h–1FFFFh 30000h–3FFFFh
SA7
0
1
0
0
X
X
X
64/32
20000h–27FFFh 40000h–4FFFFh
SA8
0
1
0
1
X
X
X
64/32
28000h–2FFFFh 50000h–5FFFFh
SA9
0
1
1
0
X
X
X
64/32
30000h–37FFFh 60000h–6FFFFh
SA10 0
1
1
1
X
X
X
64/32
38000h–3FFFFh 70000h–7FFFFh
SA11 1
0
0
0
X
X
X
64/32
40000h–47FFFh 80000h–8FFFFh
SA12 1
0
0
1
X
X
X
64/32
48000h–4FFFFh 90000h–9FFFFh
SA13 1
0
1
0
X
X
X
64/32
50000h–57FFFh A0000h–AFFFFh
SA14 1
0
1
1
X
X
X
64/32
58000h–5FFFFh B0000h–BFFFFh
SA15 1
1
0
0
X
X
X
64/32
60000h–67FFFh C0000h–CFFFFh
SA16 1
1
0
1
X
X
X
64/32
68000h–6FFFFh D0000h–DFFFFh
SA17 1
1
1
0
X
X
X
64/32
70000h–77FFFh E0000h–EFFFFh
SA18 1
1
1
1
X
X
X
64/32
78000h–7FFFFh F0000h–FFFFFh
Note:
Address range is A18:A-1 in byte mode and A18:A0 in word mode. See “Word/Byte Configuration” section for more information.
Autoselect Mode
The autoselect mode provides manufacturer and de-
vice identification, and sector protection verification,
through identifier codes output on DQ7–DQ0. This
mode is primarily intended for programming equipment
to automatically match a device to be programmed with
its corresponding programming algorithm. However,
the autoselect codes can also be accessed in-system
through the command register.
When using programming equipment, the autoselect
mode requires VID (11.5 V to 12.5 V) on address pin
A9. Address pins A6, A1, and A0 must be as shown in
Autoselect Codes (High Voltage Method) table. In addi-
tion, when verifying sector protection, the sector ad-
dress must appear on the appropriate highest order
address bits. Refer to the corresponding Sector Ad-
dress Tables. The Command Definitions table shows
the remaining address bits that are don’t care. When all
necessary bits have been set as required, the program-
ming equipment may then read the corresponding
identifier code on DQ7–DQ0.
To access the autoselect codes in-system, the host
system can issue the autoselect command via the
command register, as shown in the Command Defini-
tions table. This method does not require VID. See
“Command Definitions” for details on using the autose-
lect mode.
10
Am29F800B
Share Link: