PI5C3245 データシートの表示（PDF） - Pericom Semiconductor
部品番号
コンポーネント説明
メーカー
PI5C3245 Datasheet PDF : 5 Pages
| |||
PI5C3245
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901823-4B56i7t8,9021-2P34o56r7t89B01u21s23S4w567i8t9c0h12
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Storage Temperature ................................................................. –65°C to +150°C
Ambient Temperature with Power Applied ................................ –40°C to +85°C
Supply Voltage to Ground Potential (Inputs & Vcc Only) .......... –0.5V to +7.0V
Supply Voltage to Ground Potential (Outputs & D/O Only) ....... –0.5V to +7.0V
DC Input Voltage ......................................................................... –0.5V to +7.0V
DC Output Current ................................................................................... 120 mA
Power Dissipation ......................................................................................... 0.5W
Note:
Stresses greater than those listed under
MAXIMUM RATINGS may cause permanent dam-
age to the device. This is a stress rating only and
functional operation of the device at these or any other
conditions above those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may
affect reliability.
DC Electrical Characteristics (Over the Operating Range, TA = –40°C to +85°C, VCC =5V ±5%)
Parameters Description
Test Conditions(1)
Min. Typ(2) Max. Units
VIH
Input HIGH Voltage
VIL
Input LOW Voltage
Guaranteed Logic HIGH Level
Guaranteed Logic LOW Level
IIH
Input HIGH Current
VCC = Max., VIN = VCC
IIL
Input LOW Current
VCC = Max., VIN = GND
IOZH
High Impedance Output Current 0 ≤A, B ≤VCC
VIK
Clamp Diode Voltage
IOS
Short Circuit Current(3)
VCC = Min., IIN = –18mA
A (B) = 0V, B (A) = VCC
VH
Input Hysteresis at Control Pins
RON
Switch On Resistance(4)
VCC = Min., VIN = 0.0V, ION = 48mA
VCC = Min., VIN = 2.4V, ION = 15mA
2.0
V
–0.5
0.8
V
±1 μA
±1 μA
±1 μA
–0.7 –1.2
V
100
mA
150
mV
5
7 ohm
10
15
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at VCC = 5.0V, TA = 25°C ambient and maximum loading.
3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
4. Measured by the voltage drop between A and B pin at indicated current through the switch. ON resistance is determined by the lower of the
voltages on the two (A,B) pins.
Capacitance (TA = 25°C, f = 1 MHz)
Parameters(1)
Description
CIN
Input Capacitance
COFF
A/B Capacitance, Switch Off
CON
A/B Capacitance, Switch On
Test Conditions
VIN = 0V
VIN = 0V
VIN = 0V
Notes:
1. This parameter is determined by device characterization but is not production tested.
Max. Units
6
pF
6
pF
8
pF
06-0239
2
PS7015D 05/11/06
Share Link: 