PI74FCT245ATLE データシートの表示（PDF） - Pericom Semiconductor
部品番号
コンポーネント説明
メーカー
PI74FCT245ATLE Datasheet PDF : 7 Pages
| |||
PI74FCT245T
PI74FCT2245T(25 Ohm Series )
1122334455667788990011223344556677889900112233445566778899001122112233445566778899001122334455667788990011223344556677889900112211223344556677889900112233445566778899001122334455667788990011221122O334455c66t77a8899l00B1122i33d44i55r6677e88c99t00i11o2233n44a5566l77T8899r00a1122n1122s33c44e55i66v7788e99r0011s22
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Storage Temperature .................................................................... –65°Cto+150°C
Ambient Temperature with Power Applied .................................... –40°C to +85°C
Supply Voltage to Ground Potential (Inputs & VCC Only) ............. –0.5Vto+7.0V
Supply Voltage to Ground Potential (Outputs & D/O Only) ........... –0.5Vto+7.0V
DC Input Voltage ............................................................................ –0.5Vto+7.0V
DC Output Current ...................................................................................... 120mA
Power Dissipation ..........................................................................................0.5W
Note:
Stresses greater than those listed under MAXIMUM
RATINGS may cause permanent damage to the device.
This is a stress rating only and functional operation
of the device at these or any other conditions above
those indicated in the operational sections of this
specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may
affect reliability.
DC Electrical Characteristics (Over the Operating Range, TA = –40°C to +85°C, VCC = 5.0V ±5%)
Parameters Description
Test Conditions(1)
Min. Typ(2) Max. Units
VOH
Output HIGH Voltage VCC = Min., VIN = VIH or VIL IOH = –15.0mA
2.4 3.0
V
VOL
Output LOW Current VCC = Min., VIN = VIH or VIL
IOL = 64mA
VOL
Output LOW Current VCC = Min., VIN = VIH or VIL
IOL = 12mA (25Ω Series)
0.3 0.55 V
0.3 0.50 V
VIH
Input HIGH Voltage Guaranteed Logic HIGH Level
2.0
V
VIL
Input LOW Voltage Guaranteed Logic LOW Level
0.8 V
IIH
Input HIGH Current (Except I/O pins) VCC = Max.
VIN = VCC
1 μA
IIL
Input LOW Current (Except I/O pins) VCC = Max.
VIN = GND
–1 μA
IIH
Input HIGH Current (I/O pins Only) VCC = Max.
VIN = VCC
1 μA
IIL
Input LOW Current (I/O pins Only) VCC = Max.
VIN = GND
–1 μA
IOZH
High Impedance
VCC = MAX.
VOUT = 2.7V
1 μA
IOZL
Output Current
VOUT = 0.5V
–1 μA
VIK
Clamp Diode Voltage VCC = Min., IIN = –18 mA
–0.7 –1.2 V
IOFF
Power Down Disable VCC = GND, VOUT = 4.5V
IOS
Short Circuit Current VCC = Max.(3), VOUT = GND
100 μA
–60 –120
mA
VH
Input Hysteresis
200
mV
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at VCC = 5.0V, +25°C ambient and maximum loading.
3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
Capacitance (TA = 25°C, f = 1 MHz)
Parameters(1) Description
Test Conditions
Typ.
CIN
Input Capacitance
VIN = 0V
6
COUT
Output Capacitance
VOUT = 0V
8
Notes:
1. These Parameters are determined by device characterization but are not production tested.
Max.
Units
10
pF
12
pF
06-0207
2
PS2012E 08/08/06
Share Link: 