STK14C88-CF45TR データシートの表示（PDF） - Simtek Corporation
部品番号
コンポーネント説明
メーカー
STK14C88-CF45TR Datasheet PDF : 19 Pages
| |||
STK14C88
SOFTWARE NONVOLATILE RECALL
A software RECALL cycle is initiated with a sequence
of READ operations in a manner similar to the soft-
ware STORE initiation. To initiate the RECALL cycle,
the following sequence of E controlled READ opera-
tions must be performed:
1. Read address
2. Read address
3. Read address
4. Read address
5. Read address
6. Read address
0E38 (hex)
31C7 (hex)
03E0 (hex)
3C1F (hex)
303F (hex)
0C63 (hex)
Valid READ
Valid READ
Valid READ
Valid READ
Valid READ
Initiate RECALL cycle
Internally, RECALL is a two-step procedure. First, the
SRAM data is cleared, and second, the nonvolatile
information is transferred into the SRAM cells. After
the tRECALL cycle time the SRAM will once again be
ready for READ and WRITE operations. The RECALL
operation in no way alters the data in the nonvolatile
elements. The nonvolatile data can be recalled an
unlimited number of times.
AutoStore OPERATION
The STK14C88 can be powered in one of three
modes.
During normal AutoStore operation, the STK14C88
will draw current from VCCX to charge a capacitor
connected to the VCAP pin. This stored charge will be
used by the chip to perform a single STORE opera-
tion. After power up, when the voltage on the VCAP
pin drops below VSWITCH, the part will automatically
disconnect the VCAP pin from VCCX and initiate a
STORE operation.
Figure 2 shows the proper connection of capacitors
for automatic store operation. A charge storage
capacitor having a capacity of between 68μF and
220μF (± 20%) rated at 6V should be provided.
In system power mode (Figure 3), both VCCX and
VCAP are connected to the + 5V power supply without
the 68μF capacitor. In this mode the AutoStore func-
tion of the STK14C88 will operate on the stored sys-
tem charge as power goes down. The user must,
however, guarantee that VCCX does not drop below
3.6V during the 10ms STORE cycle.
If an automatic STORE on power loss is not required,
then VCCX can be tied to ground and + 5V applied to
VCAP (Figure 4). This is the AutoStore Inhibit mode,
in which the AutoStore function is disabled. If the
STK14C88 is operated in this configuration, refer-
ences to VCCX should be changed to VCAP throughout
this data sheet. In this mode, STORE operations may
be triggered through software control or the HSB
pin. It is not permissable to change between these
three options “on the fly”.
In order to prevent unneeded STORE operations,
automatic STOREs as well as those initiated by
externally driving HSB low will be ignored unless at
least one WRITE operation has taken place since the
most recent STORE or RECALL cycle. Software-
initiated STORE cycles are performed regardless of
whether a WRITE operation has taken place.
If the power supply drops faster than 20 μs/volt
before VCCX reaches VSWITCH, then a 2.2 ohm resistor
should be inserted between VCCX and the system
supply to avoid momentary excess of current
between Vccx and Vcap.
10kΩ∗
1
32
31
30
1
32
31
30
1
32
31
30
+
16
17
Figure 2: AutoStore Mode
16
17
Figure 3: System Power Mode
*If HSB is not used, it should be left unconnected.
Document Control #ML0014 Rev 0.3
10
February, 2007
16
17
Figure 4: AutoStore
Inhibit Mode
Share Link: 