STM-S3E データシートの表示（PDF） - Connor-Winfield Corporation
部品番号
コンポーネント説明
メーカー
STM-S3E Datasheet PDF : 16 Pages
| |||
Table 1
Symbol
VCC
VI
Ts
VTS
Parameter
Power Supply Voltage
Input Voltage
Storage Temperature
Voltage Applied to Tri-State Output
Absolute Maximum Rating
Minimum
Nominal
Maximum
-0.5
5.5
-0.5
5.5
-40
85
-0.5
5.5
Units
Volts
Volts
deg. C
Volts
Table 2
Symbol
Vcc
VIH
VIL
Recommended Operating Conditions
Parameter
Power Supply Voltage
Minimum
4.75
Nominal
Maximum
5.25
Units
Volts
High level input voltage - CMOS
2.0
5.25
Volts
Low level input voltage - CMOS
0
0.8
Volts
Table 3
Symbol
VOH
VOL
Parameter
High level output voltage,
IOH = -4.0mA, VCC = min.
Low level output voltage,
IOL = 8.0mA, VCC = max.
DC Characteristics
Minimum
Nominal
Maximum
Units
2.4
3.3
3.6
Volts
0.4
Volts
Table 4
Specifications
Parameter
Frequency Range (Sync_Out)
Frequency Range (Clk_Out)
Supply Current
Timing Reference Inputs
Jitter, Wander and Phase Transient Tolerances
Wander Generation
Wander Transfer
Jitter Generation
Jitter Transfer
Phase Transients
Sync_Out (Pin #15) Free Run Accuracy
Clock_Out (Pin #18) Accuracy
Hold Over Stability
Inital Offset
Temperature
Drift
Maximum Hold Over History
Minimum Time for Hold Over
Pull-in/ Hold-in Range
Lock Time
Lock Accuracy
RFL Alarm Limit
Specifications
1.544 MHz - 38.88 MHz
1.544 MHz - 51.84 MHz
800 mA typical, 1.2 A during warm-up (Maximum)
GR-1244-CORE 3.2.1
GR-1244-CORE 4.2-4.4, GR-253-CORE 5.4.4.3.6
GR-1244-CORE 5.3, GR-253-CORE 5.4.4.3.2
GR-1244-CORE 5.4
GR-1244-CORE 5.5, GR-253-CORE 5.6.2.3
GR-1244-CORE 5.5, GR-253-CORE 5.6.2.1
GR-1244-CORE 5.6, GR-253-CORE 5.4.4.3.3
±4.6 ppm over temperature range
±4.6 ppm over temperature range
±0.012 ppm
±0.001 ppm
±0.010 ppm
±0.001 ppm
1049 seconds
701 seconds after a reference rearrangement
±17 ppm from Free Run frequency
700 sec.
0.001 ppm (GR-1244-CORE 2.8)
±15 ppm from Free Run frequency
Notes
1.0
1.0
1.0
Notes
2.0
Notes
3.0
Notes
4.0
5.0
6.0
NOTES:
1.0: Stresses beyond those listed under Absolute Maximum Rating may cause damage
to the device. Operation beyond Recommended Conditons is not implied.
2.0: Inputs are 3.3V CMOS,5V tolerant
3.0: Logic is 3.3V CMOS
4.0: Hold Over stability is the cumulative fractional frequency offset as described by
GR-1244-CORE, 5.2
5.0: Pull-in Range is the maximum frequency deviation from nominal clock rate on the
reference inputs to the timing module that can be overcome to pull into sychronization
with the reference
6.0: After 700 seconds at stable temperature (±5° F)
Preliminary Data Sheet #: TM012 Page 3 of 16 Rev: P06 Date: 05/20/ 02
© Copyright 2002 The Connor-Winfield Corp. All Rights Reserved Specifications subject to change without notice
Share Link: 