SX1505I087TRT データシートの表示（PDF） - Semtech Corporation
部品番号
コンポーネント説明
メーカー
SX1505I087TRT Datasheet PDF : 33 Pages
| |||
ADVANCED COMMUNICATIONS & SENSING
SX1504/SX1505/SX1506
4/8/16 Channel GPIO
2 ELECTRICAL CHARACTERISTICS
2.1 Absolute Maximum Ratings
Stress above the limits listed in the following table may cause permanent failure. Exposure to absolute ratings for
extended time periods may affect device reliability. The limiting values are in accordance with the Absolute
Maximum Rating System (IEC 134). All voltages are referenced to ground (GND).
Symbol Description
Min Max
VDDMmax
VCC1,2max
VESD_HBM
VESD_CDM
VESD_MM
TA
TC
TSTG
Ilat
Main supply voltage
I/O banks supply voltage
Electrostatic handling HBM model(1)
Electrostatic handling CDM model
Electrostatic handling MM model
Operating Ambient Temperature Range
Junction Temperature Range
Storage Temperature Range
Latchup-free input pin current(2)
- 0.4
- 0.4
-
-
-
-40
-40
-55
+/-100
6.0
6.0
1500
300
200
+85
+125
+150
-
(1) Tested according to JESD22-A114A
(2) Static latch-up values are valid at maximum temperature according to JEDEC 78 specification
Table 4 - Absolute Maximum Ratings
Unit
V
V
V
V
V
°C
°C
°C
mA
2.2 Electrical Specifications
Table below applies to default registers values, unless otherwise specified. Typical values are given for TA =
+25°C, VDDM=VCC1=VCC2=3.3V.
Symbol Description
Supply
VDDM Main supply voltage
VCC1,2 I/O banks supply voltage
IDDM
Main supply current
(I2C inactive)
ICC1,2 I/O banks supply current(1)
I/Os set as Input
VIH High level input voltage
VIL Low level input voltage
VHYS Hysteresis of Schmitt trigger
ILEAK Input leakage current
CI
Input capacitance
I/Os set as Output
VOH High level output voltage
VOL Low level output voltage
IOH
High level output source
current
Low level output sink current
IOL
for the high sink I/Os
Low level output sink current
for the other I/Os.
tPV
Output data valid timing
NINT (Output)
VOL Low level output voltage
IOLM Low level output sink current
tIV Interrupt valid timing
tIR Interrupt reset timing
Conditions
Min
Typ
Max Unit
-
2.5
-
5.5 V
-
2.5
-
5.5 V
-
-
1
5
µA
-
-
1
2
µA
-
-
-
Assuming no active
pull-up/down
-
0.7*
VCC1,2
-0.4
-
-1.5
-
-
-
0.1*
VCC1,2
-
-
VCC1,2
+0.3
V
0.3*
VCC1,2
V
-
V
1.5 µA
10 pF
-
VCC1,2
– 0.3
-
VCC1,2 V
-
-0.4
-
0.3 V
-
-
-
8 mA
-
-
-
24 mA
-
Cf. Figure 9
-
-
12 mA
-
-
1.5 µs
-
-
-
-
From input data change
-
From RegInterruptSource
clearing
-
-
0.3 V
-
12 mA
-
1
µs
-
2
µs
Rev 1 – 3rd Oct. 2008
7
www.semtech.com
Share Link: 