SY100EL16VSKC データシートの表示（PDF） - Micrel

部品番号

コンポーネント説明

メーカー

SY100EL16VSKC

5V/3.3V VARIABLE OUTPUT SWING DIFFERENTIAL RECEIVER

Micrel 

Micrel, Inc.

SY100EL16VS

DC ELECTRICAL CHARACTERISTICS(1)

VEE = VEE (Min.) to VEE (Max.); VCC = GND

Symbol

Parameter

TA = –40°C

TA = 0°C

TA = +25°C

TA = +85°C

Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit

IEE

Power Supply Current

— 18 22 9 18 22 9 18 22 9 21 26 mA

VBB

Output Reference

Voltage

-1.38 — -1.26 -1.38 — -1.26 -1.38 — -1.26 -1.38 — -1.26 V

IIH

Input HIGH

-D, D — — 150 — — 150 — — 150 — — 150 µA

Current

-VCTRL — — 40 — — 40 — — 40 — — 40

VOL

Output LOW Voltage(2) -1890 — -1620 -1870 — -1680 -1870 -1775 -1680 -1870 — -1680 mV

VCTRL = VBB

VOL

Output LOW Voltage(2) -1180 — -975 -1135 — -990 -1135 -1065 -990 -1135 — -990 mV

VCTRL = VCC

VOH

Output HIGH Voltage(3) -1085 — -880 -1025 — -880 -1025 -955 -880 -1025 — -880 mV

NOTES:

1. Parametric values specified at:

100EL16VS Series:

–3.0V to –5.5V.

2. If VCTRL is an open circuit, use the VOH (max. & min.) and VOL (VCTRL = VBB: max only) limits.

3. VCC ≤ VCTRL ≤ VEE.

AC ELECTRICAL CHARACTERISTICS(1)

VEE = VEE (Min.) to VEE (Max.); VCC = GND

Symbol

Parameter

TA = –40°C

TA = 0°C

TA = +25°C

TA = +85°C

Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit

tPLH

tPHL

tskew

VPP

VCMR

tr

tf

Propagation

D (Diff) 175 — 325 175 — 325 175 — 325 205 — 355 ps

Delay to Output D (SE) 125 250 425 125 250 375 125 250 375 155 280 405

Duty Cycle Skew(2) (Diff) —

5

——

5

20 —

5

20 —

5

20 ps

Minimum Input Swing(3) 150 — — 150 — — 150 — — 150 — — mV

Common Mode Range(4) -1.3 — -0.4 -1.4 — -0.4 -1.4 — -0.4 -1.4 — -0.4 V

Output Rise/Fall Times Q — 160 260 — 160 260 — 160 260 — 160 260 ps

(20% to 80%)

NOTES:

1. Parametric values specified at:

100EL16VS Series:

–3.0V to –5.5V.

2. Duty cycle skew is the difference between a tPLH and tPHL propagation delay through a device.

3. Minimum input swing for which AC parameters are guaranteed. The device has a DC gain of ≈40 when output has a full swing.

4. The CMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified

range and the peak-to-peak voltage lies between VPP min. and 1V. The lower end of the CMR range varies 1:1 with VEE. The numbers in the spec table

assume a nominal VEE = –3.3V. Note for PECL operation, the VCMR (min) will be fixed at 3.3V – |VCMR (min)|.

M9999-083007

hbwhelp@micrel.com or (408) 955-1690

3

Share Link: