TC1262 データシートの表示（PDF） - Microchip Technology

部品番号

コンポーネント説明

メーカー

TC1262

500mA Fixed Output CMOS LDO

Microchip Technology 

TC1262

1.0 ELECTRICAL

CHARACTERISTICS

Absolute Maximum Ratings*

Input Voltage .........................................................6.5V

Output Voltage.................. (VSS – 0.3V) to (VIN + 0.3V)

Power Dissipation................Internally Limited (Note 6)

Maximum Voltage on Any Pin ........ VIN +0.3V to -0.3V

Operating Temperature Range...... -40°C < TJ < 125°C

Storage Temperature.......................... -65°C to +150°C

*Stresses above those listed under "Absolute Maximum

Ratings" may cause permanent damage to the device. These

are stress ratings only and functional operation of the device

at these or any other conditions above those indicated in the

operation sections of the specifications is not implied.

Exposure to Absolute Maximum Rating conditions for

extended periods may affect device reliability.

TC1262 ELECTRICAL SPECIFICATIONS

Electrical Characteristics: VIN = VOUT + 1V, IL = 100µA, CL = 3.3µF, TA = 25°C, unless otherwise noted. Boldface type

specifications apply for junction temperatures of -40°C to +125°C.

Symbol

Parameter

Min

Typ

Max

Units

Test Conditions

VIN

Input Operating Voltage

2.7

—

6.0

V Note 7

IOUTMAX

Maximum Output Current

500

—

—

mA

VOUT

Output Voltage

—

VR ±0.5%

—

V Note 1

VR – 2.5%

—

VR + 2.5%

∆VOUT/∆T

VOUT Temperature Coefficient

—

40

—

ppm/°C Note 2

∆VOUT/∆VIN Line Regulation

—

.003

0.35

%/V (VR + 1V) ≤ VIN ≤ 6V

∆VOUT/VOUT Load Regulation

—

0.002

0.01

%/mA IL = 0.1mA to IOUTMAX (Note 3)

VIN-VOUT

Dropout Voltage

—

20

30

mV IL = 100µA

—

60

130

IL = 100mA

—

200

390

IL = 300mA

350

650

IL = 500mA (Note 4)

IDD

Supply Current

—

80

130

µA IL = 0

PSRR

Power Supply Rejection Ratio

—

64

—

dB FRE ≤ 1kHz

IOUTSC

Output Short Circuit Current

—

1200

—

mA VOUT = 0V

∆VOUT/∆PD Thermal Regulation

—

0.04

—

V/W Note 5

eN

Output Noise

—

260

—

nV/√Hz IL = IOUTMAX, FRE = 10kHz

Note

1: VR is the regulator output voltage setting.

2: TC VOUT = (VOUTMAX – VOUTMIN) x 106

VOUT x ∆T

3: Regulation is measured at a constant junction temperature using low duty cycle pulse testing. Load regulation is tested over a load range

from 0.1mA to the maximum specified output current. Changes in output voltage due to heating effects are covered by the thermal

regulation specification.

4: Dropout voltage is defined as the input to output differential at which the output voltage drops 2% below its nominal value measured at a

1V differential.

5: Thermal Regulation is defined as the change in output voltage at a time T after a change in power dissipation is applied, excluding load or

line regulation effects. Specifications are for a current pulse equal to ILMAX at VIN = 6V for T = 10 msec.

6: The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable junction temperature and the

thermal resistance from junction-to-air (i.e., TA, TJ, θJA). Exceeding the maximum allowable power dissipation causes the device to initiate

thermal shutdown. Please see Section 4.0 Thermal Considerations for more details.

7: The minimum VIN has to justify the conditions: VIN ≥ VR + VDROPOUT and VIN ≥ 2.7V for IL = 0.1mA to IOUTMAX.

DS21373B-page 2

© 2002 Microchip Technology Inc.

Share Link: