TDA3681JR データシートの表示（PDF） - Philips Electronics

部品番号

コンポーネント説明

メーカー

TDA3681JR

Multiple voltage regulator with switch and ignition buffer

Philips Electronics 

Philips Semiconductors

Multiple voltage regulator with switch and

ignition buffer

Product specification

TDA3681

FEATURES

General

• Extremely low noise behaviour and good stability with

very small output capacitors

• Second supply pin for regulators 3 and 4 to reduce

power dissipation (e.g. via a DC-to-DC converter)

• Three VP-state controlled regulators (regulators 1, 3

and 4) and a power switch

• Regulator 2, reset and ignition buffer operational during

load dump and thermal shutdown

• Combined control pin for switching regulators 1 and 3

• Separate control pins for switching regulator 4 and the

power switch

• Supply voltage range from −18 to +50 V

• Low quiescent current in standby mode (when

regulators 1, 3 and 4 and power switch are switched off

and ignition input is low)

• Hold output for low VP (regulators 1, 3 and 4 and power

switch off)

• Hold output when one of regulators 1 and 3 and/or 4 is

out of regulation

• Hold output for foldback mode of power switch and

regulators 1, 3 and 4

• Hold output for load dump and temperature protection

• Reset (push-pull output stage) for regulator 2 and hold

output (open-collector output)

• Adjustable reset delay time

• High supply voltage ripple rejection

• Backup capacitor for regulator 2

• One independent ignition buffer (active HIGH).

Protections

• Reverse polarity safe (down to −18 V without high

reverse current)

• Able to withstand voltages up to 18 V at the outputs

(supply line may be short-circuited)

• ESD protection on all pins

• Thermal protections

• Load dump protection

• Foldback current limit protection for regulators 1, 2, 3

and 4

• Delayed second current limit protection for the power

switch (at short-circuit)

• The regulator outputs and the power switch are

DC short-circuit safe to ground and supply (VP).

GENERAL DESCRIPTION

The TDA3681 is a multiple output voltage regulator with a

power switch and an ignition buffer. It is intended for use in

car radios with or without a microcontroller. The TDA3681

contains the following:

• Four fixed voltage regulators with a foldback current

protection (regulators 1, 2, 3 and 4). Regulator 2, which

is intended to supply a microcontroller, also operates

during load dump and thermal shutdown

• Regulators 3 and 4 have a second supply pin that can

be connected to a lower supply voltage (>6.5 V) to

reduce the power dissipation

• A power switch with protection, operated by a control

input

• Reset and hold outputs that can be used to interface

with the microcontroller; the reset signal can be used to

call up the microcontroller

• Both supply pins can withstand load dump pulses and

negative supply voltages

• Regulator 2, which is in regulation at a backup voltage

above 6.5 V

• A provision for the use of a reserve supply capacitor that

will hold enough energy for regulator 2 (5 V continuous)

to allow a microcontroller to prepare for loss of voltage

• An ignition input Schmitt trigger with push-pull output

stage.

ORDERING INFORMATION

TYPE

NUMBER

TDA3681J

TDA3681JR

TDA3681TH

NAME

DBS17P

DBS17P

HSOP20

PACKAGE

DESCRIPTION

plastic DIL-bent-SIL power package; 17 leads (lead length 7.7 mm)

plastic DIL-bent-SIL (special bent) power package; 17 leads

(lead length 12 mm)

plastic, heatsink small outline package; 20 leads; low stand-off height

VERSION

SOT243-3

SOT475-1

SOT418-2

2002 Apr 10

2

Share Link: