TS1582CM5 データシートの表示（PDF） - TSC Corporation
部品番号
コンポーネント説明
メーカー
TS1582CM5 Datasheet PDF : 9 Pages
| |||
TS1582
3A Dual Input LDO
Absolute Maximum Rating
Parameter
Input Supply Voltage
V Power
V Control
Power Dissipation
Operating Junction Temperature Range
Storage Temperature Range
Lead Soldering Temperature (260oC)
Symbol
Vpower
Vcontrol
PD
TJ
TSTG
Value
7
13
Internally Limited
0 ~ +125
-65 ~ +150
10
Units
V
W
oC
oC
S
Electrical Characteristics Ta=+25°C, Ccontrol=Cpower=Cout=10uF unless Specified
Parameter
Conditions
Min Typ Max Unit
Reference Voltage
(Adj. Voltage Versions)
VCONTROL = 4.5V, VPOWER = 2.05V, IO = 10mA
VCONTROL = 4.5V, VPOWER = 2.05V,
IO = 10mA to 3A
1.238
1.262
1.250
V
1.230
1.270
Output Voltage
VCONTROL = 5V, VPOWER =VOUT+0.8V, IO = 10mA
-1.0
+1.0
(Fixed Voltage Versions)
VCONTROL = 5V, VPOWER = VOUT +0.8V,
VOUT
%
-1.6
+1.6
IO = 10mA to 3A
Line Regulation
Load Regulation
VCONTROL = (VOUT +1.5V) to 12V,
VPOWER = (VOUT +0.8V) to 5.5V, IO = 10mA
VCONTROL = (VOUT +2.5V),
VPOWER = (VOUT +0.8V), IO = 10mA to 3A
--
0.04
0.2
%
--
0.08
0.4
%
Mini. Load Current (Note 2) VCONTROL =5V, VPOWER= 3.3V, VADJ=0V
--
5
10
mA
Control Pin Current
(Note 3)
Adjust Pin Current
VCONTROL = (VOUT +2.5V),
VPOWER = (VOUT +0.8V), IO = 10mA to 3A
VCONTROL = 2.75V, VPOWER = 2.05, VADJ = 0V,
IO = 10mA
--
80
135
mA
--
50
120
uA
Current Limit
Ripple Rejection
Thermal Regulation
VPOWER - VOUT = 3V
VCONTROL = VPOWER = 5V, VRIPPLE = 1V,
IO = 2.3A, f = 120kHz
30mS pulse
5.5
6.8
--
60
80
--
--
0.003
--
A
dB
%/W
Dropout Voltage (Note 4)
VCONTROL = (VOUT +2.5V), IO = 3A
--
0.55 0.70
V
Note1: VOUT = VSENSE, VADJ = 0V unless otherwise specified.
Note2: For the adjustable device the minimum load current is the minimum current required to maintain regulation,
normally the current in the resistor divider used to set the output voltage is selected to meet the minimum load
current requirement.
Note3: The control pin current is the drive current required for the output transistor, this current will track output current
with a ratio of about 1:100
Note4: If the same voltage is input to both VPOWER and VCONTROL, then the dropout voltage will become 1.3V maximum,
and minimum input/output voltage required to maintain 1% regulation.
2/9
Version: A07
Share Link: 