UPB1008K-A データシートの表示（PDF） - California Eastern Laboratories.
部品番号
コンポーネント説明
メーカー
UPB1008K-A Datasheet PDF : 10 Pages
| |||
UPB1008K
ELECTRICAL CHARACTERISTICS (TA = 25°C, VCC = 3.0 V, unless otherwise specified)
SYMBOLS
PARAMETERS AND CONDITIONS
UNITS
MIN
TYP
ICC
Total Circuit Current, No Signals
mA
14
18
VCC
Supply Voltage
V
2.7
3.0
ICC_PD Power down current, PIN 13 = VIL
µA
–
1
ICC rf
RF Block Circuit Current (pin 3), No signal
µA
0.4
0.5
ICC lo
VCO Block Circuit Current (pin 7), No signal
mA
4.1
5.6
ICC pll PLL Block Circuit Current (pin 9), No signal
mA
2.7
3.6
ICC bb Baseband Block Circuit Current (pin 23), No signal,
mA
2.5
3.4
open load
ICC if IF Block Circuit Current (pin 28) , No signal
mA
2.7
3.7
ICC lna Pre-Amplifier Open Connector Current (pin 36),
mA
1.0
1.4
No signal
MAX
23.5
3.3
10
0.7
7.2
4.7
4.3
4.7
1.8
LNA/RF DOWNCONVERTER
(fRFin = 1575.42 MHz, f1stLOin = 1400 MHz, PLO = -10 dBm, f1stIF = 175 MHz, Pin 13: VIL = 3 V, ZL differential = 32Ω & ZS = Γopt)
SYMBOLS
PARAMETERS AND CONDITIONS
UNITS
MIN
CGLNA_MIX Power conversion gain from 2nd LNA/mixer to 1st IF,
dB
18
PRFin = -50 dBm
NFLNA_MIX Noise Figure of 2nd LNA/mixer(SSB), Input matched
dB
–
P1dBLNA_MIX 1 dB Compression refer to source, Input matched
dBm
–
ZLNAin RF Input Impedance of LNA
Ohm
–
ZMIXout IF Output Impedance of Mixer
Ohm
ALO-IF
Local Signal Leak to IF, f1stLOin=1400 MHz,
PLO = 0 dBm
dBm
–
ALO-RF
Local Signal Leak to RF, f1stLOin=1400 MHz,
PLO = 0 dBm
dBm
–
PLL
SYMBOLS
PARAMETERS AND CONDITIONS
UNITS
MIN
ICPOH
PLL Charge Pump High Side Current @ VCPout = VCC/2
µA
–
ICPOL
PLL Charge Pump Low Side Current @ VCPout = VCC/2
µA
–
fPD
Phase Comparison Frequency
MHz
–
CRYSTAL OSCILLATOR/REVERENCE AMPLIFIER BLOCK
SYMBOLS
PARAMETERS AND CONDITIONS
UNITS
MIN
VREFin Reference input minimum level
mVpp
50
fREF
Input Frequency of Reference Input
MHz
–
VT
VCO Control Voltage, PLL Locked
V
0.8
C/N
VCO C/N, 1kHz, Loop band width = 5 kHz
dBc/Hz
57
AGC AMPLIFIER, I-Q DEMODULATOR, and ADC BLOCK(f1stIFin = 175 MHz, Zin = 600Ω)
SYMBOLS
PARAMETERS AND CONDITIONS
UNITS
MIN
CGAGC/MIX Maximum voltage conversion gain of AGC amplifier/
dB
–
I-Q mixer, Pin = -60 dBm, VAGC = 0.5 V, Unmatched
Minimum voltage conversion gain of AGC amplifier/
dB
–
I-Q mixer, Pin = -60 dBm, VAGC = 2.0 V, Unmatched
AAGC/MIX AGC control range, VAGC = 0.5 V to 2 V
dB
25
P1dBAGC
1 dB compression input to AGC amplifier,
set voltage gain = 30 dB
dBm
–
TYP
23
5
-38
31
32
-35
-50
TYP
200
-200
13.5
TYP
200
27
1.5
62
TYP
30
-15
45
-45
MAX
28
–
–
–
–
–
MAX
–
–
–
MAX
–
–
2.2
–
MAX
–
–
–
–
VAGC
AGC control voltage
V
0.5
BW
3dB Mixer Bandwidth
MHz
–
VIQ-C
IQ BalanceControl Voltage, Gain(Ich) = Gain (Qch)
V
–
AIQ-C
IQ Balance Control Gain Range, VIQ-C = 0 to 3 V
dB
4.0
Duty
Ich Mag Bit Output Pulse Duty, P1stIFin = -84 dBm
%
50
Ich
VAGC = 0.5 V, VIQ-C = 0 V
Duty
Qch Mag Bit Output Pulse Duty, PIF2in = -88 dBm
%
50
Qch
VAGC = 0.5 V, VIQ-C = 0 V
BASEBAND AMPLIFIER BLOCK (ZS = 2kΩ & ZL = 2 kΩ)
SYMBOLS
PARAMETERS AND CONDITIONS
UNITS
MIN
VBBOH Baseband output logic high, CL = 10 pF
V
2.0
VBBOL Baseband output logic low, CL = 10 pF
V
0
–
10
2.1
6.5
–
–
TYP
–
–
2.0
–
2.8
–
–
–
MAX
–
0.5
Share Link: 