UPB582A データシートの表示（PDF） - NEC => Renesas Technology
部品番号
コンポーネント説明
メーカー
UPB582A Datasheet PDF : 4 Pages
| |||
UPB582A, UPB582B, UPB582C
ABSOLUTE MAXIMUM RATINGS1 (TA = 25°C)
SYMBOLS
PARAMETERS UNITS RATINGS
VCC Supply Voltage
V
-0.5 to 6.0
VIN
Input Voltage
V -0.5 to VCC +0.5
PIN
Input Power
dBm
+10
PD
Total Power Dissipation
UPB582B2
mW
UPB582A
mW
UPB582C
mW
1500
750
600
TOP Operating Temperature
UPB582B
UPB582A, C
°C
-55 to +125
°C
-55 to +85
TSTG
Storage Temperature
UPB582B
UPB582A
UPB582C
°C
-65 to +200
°C
-55 to +200
°C
-55 to +125
Notes
1. Operation in excess of any one of these parameters may result in
permanent damage.
2. TA = Absolute Maximum Operating Temperature.
TYPICAL PERFORMANCE CURVES
(VCC = 5 V, TA = 25°C )
UPB582A
INPUT POWER vs. FREQUENCY
40
30
20
PIN MAX
10
Guaranteed Operating
0
Window
PIN MIN
-10
-20
-30
-40
0.5
1
2
5
Frequency, f (GHz)
UPB582B
INPUT POWER vs. FREQUENCY AND
TEMPERATURE
20
10
TA = 85˚C
TA = 25˚C
0
TA = -20˚C
VCC = 5 V
-10
-20
-30
0 0.5 1 1.5 2
2.5 3
3.5
Frequency, f (GHz)
RECOMMENDED
OPERATING CONDITIONS (TA = 25°C)
SYMBOL
VCC
TOP
PARAMETER
Supply Voltage
Operating Temperature
UPB582B
UPB582A, C
UNITS
V
°C
°C
RATINGS
4.5 to 5.5
-40 to +85
-20 to +75
Note: Because of the high internal gain and gain compression of the
UPB582, this device is prone to self-oscillation in the absence of an RF
input signal. If the device will be used in an application where DC power
will be applied in the absence of an RF input signal, this self-oscillation
can be suppressed by any of the following means:
* Add a shunt resistor from the RF input line to ground. The
blocking capacitor should be between the resistor and the
UPB582, but physical separation should be minimized. Typically a
resistor value between 50 and 100 ohms will suppress the self-
oscillation.
* Apply a DC offset voltage of +3.0 volts to the INPUT pin. The
voltage source should be isolated from the INPUT pin by a series
1000 ohm resistor.
* Apply a DC offset voltage of +1.5 volts to the BYPASS pin. The
voltage source should be isolated from the BYPASS pin by a
series 1000 ohm resistor.
All these approaches reduce the input sensitivity of the UPB582 (by as
much as 3 dB for the example of a 50 ohm shunt resistor), but otherwise
have no affect on the reliability or other electrical characteristics of this
device.
UPB582B
INPUT POWER vs. FREQUENCY
20
10
0
Guaranteed
Operating Window
-10
-20
-30
0
-80
-90
-100
-110
-120
-130
-140
-150
-160
-170
-180
1
0.5 1 1.5 2 2.5 3 3.5
Frequency, f (GHz)
UPB582A
SSB PHASE NOISE vs.
OFFSET FROM CARRIER
fIN = 500 MHz
TA = 25˚C
10
100
1K
10K 100K 1M
Offset from Carrier (Hz)
Share Link: 