708X1PA1I3HC01 データシートの表示（PDF） - Unspecified

部品番号

コンポーネント説明

メーカー

708X1PA1I3HC01

Rosemount™ 708 Wireless Acoustic Transmitter

Unspecified 

Rosemount 708

February 2017

Product Certifications

Rev 2.1

European Union Directive Information

A copy of the EU Declaration of Conformity can be found at the

end of the Quick Start Guide. The most recent revision of the EU

Declaration of Conformity can be found at

Emerson.com/Rosemount.

Telecommunication Compliance

All wireless devices require certification to ensure that they

adhere to regulations regarding the use of the RF spectrum.

Nearly every country requires this type of product certification.

Emerson is working with governmental agencies around the

world to supply fully compliant products and remove the risk of

violating country directives or laws governing wireless device

usage.

USA

I5 U.S.A. Intrinsically Safe (IS)

Certificate: (FM) 3043245

Standards: FM Class 3600 – 1998, FM Class 3610 – 2010,

FM Class 3810 – 2005, NEMA 250 – 2003,

ANSI/IEC 60529 – 2004

Markings: IS CL I, DIV 1, GP A, B, C, D T4;

CL 1, Zone 0 AEx ia IIC T4;

T4(–40 °C ≤ Ta ≤ +70 °C) when installed per

Rosemount drawing 00708-1000; Type 4X

Special Conditions for Safe Use (X):

1. The Rosemount 708 Wireless Acoustic Transmitter shall

only be used with the 701PGNKF Rosemount SmartPower

battery pack.

2. Potential Electrostatic charging Hazard – See instructions.

FCC and IC

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following conditions: This device may not cause

harmful interference. This device must accept any interference

received, including interference that may cause undesired

operation. This device must be installed to ensure a minimum

antenna separation distance of 20 cm from all persons.

Ordinary Location Certification

As standard, the transmitter has been examined and tested to

determine that the design meets the basic electrical,

mechanical, and fire protection requirements by a nationally

recognized test laboratory (NRTL) as accredited by the Federal

Occupational Safety and Health Administration (OSHA).

Installing in North America

The US National Electrical Code® (NEC) and the Canadian

Electrical Code (CEC) permit the use of Division marked

equipment in Zones and Zone marked equipment in Divisions.

The markings must be suitable for the area classification, gas,

and temperature class. This information is clearly defined in the

respective codes.

Canada

I6 Canada Intrinsically Safe

Certificate: (CSA) 2439890

Standards: CAN/CSA C22.2 No. 0-M91,

CAN/CSA C22.2 No. 94-M91,

CSA Std C22.2 No. 142-M1987,

CSA Std C22.2 No. 157-92,

CSA Std C22.2 No. 60529:05

Markings: I.S. CL I, DIV 1, GP A, B, C, D when installed per

Rosemount drawing 00708-1001; T3C; Type

4X

Europe

I1 ATEX Intrinsic Safety

Certificate: Baseefa11ATEX0174X

Standards: EN 60079-0: 2012, EN 60079-11: 2012

Markings: II 1 G Ex ia IIC T4 Ga, T4 (–40 °C ≤ Ta ≤ +70 °C)

Special Conditions for Safe Use (X):

1. The plastic enclosure of the Rosemount 708 may

constitute a potential electrostatic ignition risk and must

not be rubbed or cleaned with a dry cloth.

2. The Model 701PGNKF Power Module may be replaced in a

hazardous area. The power module has a surface resistivity

greater than 1GΩ and must be properly installed in the

wireless device enclosure. Care must be taken during

transportation to and from the point of installation to

prevent electrostatic charge build-up.

8

Emerson.com/Rosemount

Share Link: