DCM40 データシートの表示（PDF） - Honeywell International

部品番号

コンポーネント説明

メーカー

DCM40

Pressure switches and pressure monitors for overpressure

Honeywell International 

Mechanical pressure switches

23

Principal technical data

Principal technical data

Valid for all pressure switches of the DCM, DNM, DWAM, DWAMV, SDBAM, VCM, VNM, DNM, DWR, DGM,

DNS and DDCM series that have a microswitch. The technical data of type-tested units may differ slightly

(please refer to particular type sheet).

Standard version

Plug connection

Terminal connection

…200

…300

Switch housing

Diecast aluminium GDAISi 12

Pressure connection G 1/2" external thread (pressure gauge

connection) and G 1/4" internal thread.

1/4" internal thread for DDCM differential

pressure switches

Switching function and Floating changeover contact.

connection scheme With rising pressure

(applies only to version single pole switching

with microswitch)

from 3–1 to 3–2.

Switching capacity

8 A at 250 VAC

(for microswitches with 5 A at 250 VAC inductive

a silver contact)

8 A at 24 VDC

0.3 A at 250 VDC

min. 10 mA, 12 VDC

Mounting position

Preferably vertical (see technical data sheet)

Protection class

IP 54

(in vertical position)

Electrical connection Plug connection

Cabel entry

Pg 11

Ambient temperature –25 to +70 °C (exceptions:

DWAM, DWAMV, SDBAM series –20 to +70 °C

DGM and FD series: –25 to +60 °C

DCM4016, 4025, 1000,

VCM4156: –15 to +60 °C)

Switching point

Adjustable using the setting spindle (for 300 device:

after removing switch housing cover)

Hysteresis

Adjustable or not adjustable

(see Product Summary)

Medium temperature Max. 70 °C, briefly 85 °C

Relative humidity

15 to 95 % (non-condensing)

Diecast aluminium GDAISi 12

G 1/2" external thread (pressure gauge

connection) and G 1/4" internal thread.

1/4" internal thread for DDCM differential

pressure switches

Floating changeover contact.

With rising pressure

single pole switching

from 3–1 to 3–2

3 A at 250 VAC

2 A at 250 VAC inductive

3 A at 24 VDC

0.1 A at 250 VDC

min. 2 mA, 24 VDC

Vertical

IP 65

Terminal connection

M 16 x 1.5

–25 to +70 °C (exceptions:

DWAM, DWAMV, SDBAM series –20 to +70 °C

DGM and FD series: –25 to +60 °C

DCM4016, 4025, 1000,

VCM4156: –15 to +60 °C)

Adjustable using the setting spindle once the

switch housing cover is removed

Adjustable or not adjustable

(see Product Summary)

Max. 70 °C, briefly 85 °C

15 to 95 % (non-condensing)

Vacuum

Repetition accuracy

of switching points

Vibration resistance

Mechanical durability

(pressure sensor)

Electronical durability

(microswitch)

Isolation values

Oil and grease-free

Higher medium temperatures are possible provided the above limits for the switching device are

ensured by suitable measures (e.g. siphon). All pressure switches can operate under vacuum.

This will not damage the device (exception DCM1000).

< 1 % of the working range (for pressure ranges > 1 bar).

No significant deviations up to 4 g.

With sinusoidal pressure application and room temperature, 10 x 106 switching cycles. The expected life

depends to a very large extent on the type of pressure application, therefore this figure can serve only as

a rough estimate. With pulsating pressure or pressure impacts in hydraulic systems, pressure surge

reduction is recommended.

100.000 switching cycles at nominal current 8 A, 250 VAC.

A reduced contact load increases the number of possible switching cycles.

Overvoltage category III, contamination class 3, reference surge voltage 4000 V.

Conformity to DIN VDE 0110 is confirmed.

The parts of all pressure switches in contact with the medium are oil and grease-free

(except the HCD…and DPS…series). The sensors are hermetically sealed and contain no seals

(also see ZF1979, special packing).

Share Link: