MX802 データシートの表示（PDF） - MX-COM Inc

部品番号

コンポーネント説明

メーカー

MX802

DVSR CODEC

MX-COM Inc  

DVSR CODEC

10

MX802

4.1.3.3 Speech Playback

Speech playback is controlled by similar commands using the Speech Play counters and Play Command

Buffer:

4.1.3.3.1 64H PLAY “N” PAGES – START PAGE “X” (immediate)

65H PLAY “N” PAGES – START PAGE “X” (buffered)

As soon as the Play Command had completed, the “Play Command Complete” bit in the Status Register is

set, and an Interrupt Request is generated (if enabled).

If no “next” command is waiting in the Play Command Buffer when a speech play command finishes, a

continuous idle code (0101…0101) will be fed to the delta decoder.

Speech data is stored or recovered at the selected Encode or Decode sample rate (Table 5). Store or Play

Command Complete bits in the Status Register are cleared by the next Store or Play Command received from

the microcontroller, or by a General Reset (01H).

4.1.3.4 Store/Play Speech Synchronization (Table 6)

This capability is provided primarily for Time Domain Scrambling applications.

Speech Synchronization bits in the Control Register will produce the effects described below:

4.1.3.4.1 No Speech Sync Set:

Store and Play operations may take place completely independently.

4.1.3.4.2 Store after Play:

The next buffered store command will start on completion of a play command, while the next play command

sequence (if any) continues normally.

4.1.3.4.3 Play after Store:

The next buffered play command will start on completion of a store command, while the next store command

sequence (if any) continues normally.

These actions will continue while Speech Sync bits are set.

4.1.4 Data Handling

For the purpose of storing data sent via C-BUS from the microcontroller, the memory (DRAM) is divided into

“data pages” of 64 bits (8 bytes).

A 256kbit DRAM contains

4096 data pages.

A 1Mbit DRAM contains 16384 data pages.

4Mbit DRAM contains 65536 data pages.

In accordance with C-BUS timing specifications, data is handled 8 bits (1 byte) at a time, although any

number of 8-bit blocks of data may be written to or read from the DRAM by a single command.

Data transfer is terminated by the Chip Select line going to a logic “1.”

4.1.4.1 C-BUS Data Transfer Limitations

For those commands which transfer data over the C-BUS between DRAM and the microcontroller (Write and

Read data), the C-BUS serial clock rate is limited to a maximum of:

125kHz if the VSR Codec is executing store and play commands.

250kHz if no speech Store or Play commands are active.

This limitation is due to the rate at which data goes into and out of the DRAM. All other commands and

replies (Control, Status, Reset) may use a maximum clock rate of 500kHz. See Figure 4.

4.1.4.2 Read Data

4.1.4.2.1 67H READ DATA -- START PAGE “P”

This command sets the Data Read Counter to “P,” page, and then reads data bytes from successive DRAM

locations, sending them to the microcontroller as Reply Data bytes. The Data Read Counter is incremented

by 1 for each bit read.

4.1.4.2.2 69H READ DATA CONTINUE

This command reads data bytes from successive DRAM locations determined by the Data Read Counter,

incrementing the counter by 1 for each bit read.

1998 MX-COM, Inc.

www.mxcom.com Tel: 800 638 5577 336 744 5050 Fax: 336 744 5054

Doc. # 20480033.008

4800 Bethania Station Road, Winston-Salem, NC 27105-1201 USA

All trademarks and service marks are held by their respective companies.

Share Link: