AD741CN データシートの表示（PDF） - Analog Devices
部品番号
コンポーネント説明
メーカー
AD741CN Datasheet PDF : 6 Pages
| |||
AD741 Series–SPECIFICATIONS (typical @ +25؇C and ؎15 V dc, unless otherwise noted)
Model
AD741C
AD741
AD741J
Min Typ Max Min Typ Max Min Typ Max Units
OPEN-LOOP GAIN
RL = 1 kΩ, VO = ± 10 V
RL = 2 kΩ, VO = ± 10 V
TA = min to max RL = 2 kΩ
20,000 200,000
15,000
OUTPUT CHARACTERISTICS
Voltage @ RL = 1 kΩ, TA = min to max
Voltage @ RL = 2 kΩ, TA = min to max ؎10 ± 13
Short Circuit Current
25
50,000 200,000
25,000
؎10 ± 13
25
50,000 200,000
V/V
V/V
25,000
V/V
؎10 ± 13
V
V
25
mA
FREQUENCY RESPONSE
Unity Gain, Small Signal
1
1
1
MHz
Full Power Response
10
10
10
kHz
Slew Rate
0.5
0.5
0.5
V/µs
Transient Response (Unity Gain)
Rise Time CL ≤ 10 V p-p
0.3
0.3
0.3
µs
Overshoot
5.0
5.0
5.0
%
INPUT OFFSET VOLTAGE
Initial, RS ≤ 10 kΩ, Adjust to Zero
TA = min to max
Average vs. Temperature (Untrimmed)
vs. Supply, TA = min to max
INPUT OFFSET CURRENT
Initial
TA = min to max
Average vs. Temperature
1.0 6.0
1.0 7.5
20
200
40
300
1.0 5.0
1.0 6.0
20
200
85
500
1.0 3.0 mV
4.0 mV
20 µV/°C
30
100 µV/V
5
50 nA
100 nA
0.1
nA/°C
INPUT BIAS CURRENT
Initial
TA = min to max
Average vs. Temperature
80
500
120 800
80
500
300 1,500
40
200 nA
400 nA
0.6
nA/°C
INPUT IMPEDANCE DIFFERENTIAL 0.3 2.0
0.3 2.0
1.0
MΩ
INPUT VOLTAGE RANGE1
Differential, max Safe
Common-Mode, max Safe
Common-Mode Rejection,
RS = ≤ 10 kΩ, TA = min to max,
VIN = ± 12 V
± 12 ± 13
70
90
± 12 ± 13
70
90
± 30 V
± 15
V
80
90
dB
POWER SUPPLY
Rated Performance
Operating
Power Supply Rejection Ratio
Quiescent Current
Power Consumption
TA = min
TA = max
± 15
30
150
1.7 2.8
50
85
± 15
±5
30
150
1.7 2.8
50
85
60
100
45
75
± 15
V
± 18 V
µV/V
2.2 3.3 mA
50
85 mW
mW
mW
TEMPERATURE RANGE
Operating Rated Performance
0
Storage
–65
+70 –55
+150 –65
+125 0
+150 –65
+70 °C
+150 °C
NOTES
1For supply voltages less than ± 15 V, the absolute maximum input voltage is equal to the supply voltage.
All min and max specifications are guaranteed. Specifications shown in boldface are tested on all production units at final electrical test. Results from those tests are
used to calculate outgoing quality levels.
Specifications subject to change without notice.
–2–
REV. A
Share Link: 