AS29F010 データシートの表示（PDF） - Austin Semiconductor
部品番号
コンポーネント説明
メーカー
AS29F010 Datasheet PDF : 26 Pages
| |||
Austin Semiconductor, Inc.
FLASH
AS29F010
WRITE OPERATION STATUS
Bit I may be read at any address, and is valid after the rising
The device provides several bits to determine the status of
a write operation: DQ3, DQ5, DQ6, and DQ7. Table 5 and the
following subsections describe the functions of these bits. DQ7
and DQ6 each offer a method for determining whether a
program or erase operation is complete or in progress. These
three bits are discussed first.
edge of the final WE\ pulse in the command sequence (prior to
the program or erase operation), and during the sector erase
time-out.
During an Embedded Program or Erase algorithm
operation, successive read cycles to any address cause DQ6 to
toggle. (The system may use either OE\ or CE\ to control the
read cycles.) When the operation is complete, DQ6 stops
DQ7: Data\ Polling
toggling.
The Data\ Polling bit, DQ7, indicates to the host system
After an erase command sequence is written, if all sectors
whether an Embedded Algorithm is in progress or completed.
Data\ Polling is valid after the rising edge of the final WE\ pulse
FIGURE 3: DATA\ POLLING ALGORITHM
in the program or erase command sequence.
During the Embedded Program algorithm, the device
outputs on DQ7 the complement of the datum programmed to
DQ7. When the Embedded Program algorithm is complete, the
device outputs the datum programmed to DQ7. The system
must provide the program address to read valid status
information on DQ7. If a program address falls within a
protected sector, Data\ Polling on DQ7 is active for
approximately 2µs, then the device returns to reading array
data.
During the Embedded Erase algorithm, Data\ Polling
produces a “0” on DQ7. When the Embedded Erase algorithm
is complete, Data\ Polling produces a “1” on DQ7. This is
analogous to the complement/true datum output described for
the Embedded Program algorithm: the erase function changes
all the bits in a sector to “1”; prior to this, the device outputs
the “complement,” or “0”. The system must provide an
address within any of the sectors selected for erasure to read
valid status information on DQ7.
After an erase command sequence is written, if all sectors
selected for erasing are protected, Data\ Polling on DQ7 is
active for approximately 100µs, then the device returns to
reading array data. If not all selected sectors are protected, the
Embedded Erase algorithm erases the unprotected sectors, and
ignores the selected sectors that are protected.
When the system detects DQ7 has changed from the
complement to true data, it can read valid data at DQ7-DQ0 on
the following read cycles. This is because DQ7 may change
asynchronously with DQ0-DQ6 while Output Enable (OE\) is
asserted low. The Data\ Polling Timings (During Embedded
Algorithms) figure in the “AC Characteristics” section
illustrates this.
Table 5 shows the outputs for Data\ Polling on DQ7.
Figure 3 shows the Data\ Polling algorithm.
NOTE:
DQ6: Toggle Bit I
Toggle bit I on DQ6 indicates whether an Embedded
Program or Erase algorithm is in progress or complete. Toggle
1) VA = Valid address for programming. During a sector erase operation,
a valid address is an address within any sector selected for erasure. During
chip erase, a valid address is any non-protected sector address.
2) DQ7 should be rechecked even if DQ5 = “1” because DQ7 may change
simultaneously with DQ5.
AS29F010
Rev. 2.3 12/08
10
Austin Semiconductor, Inc. reserves the right to change products or specifications without notice.
Share Link: 