DatasheetQ Logo
Electronic component search and free download site. Transistors,MosFET ,Diode,Integrated circuits

TH8052.2 データシートの表示(PDF) - Melexis Microelectronic Systems

部品番号
コンポーネント説明
メーカー
TH8052.2
Melexis
Melexis Microelectronic Systems  Melexis
TH8052.2 Datasheet PDF : 14 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
TH8053
Fault Tolerant Low Speed CAN Transceiver
Dynamic Characteristics
The devices R1, C1 and C2 which values are given in the column "Condition" of the table below refer to
the test-schematic schown in Figure 4, ”Test Circuit for Dynamic Characteristics”
For the definition of propagation delay and transitions times see Figure. 2 - TH8053 Timing Diagram
Parameter
Symbol Conditions
Min Typ Max Unit
Transition time of CANH and CANL
from recessive to dominant
trec-dom
10% to 90%, C1=10nF, C2=0,
R1=100
0.6
1
Transition time of CANH and CANL
from dominant to recessive
tdom-rec
10% to 90%, C1=1nF, C2=0,
R1=100
0.2
0.3
C1=100pF, C2=0, R1=100, no
bus failures and bus failures 1,
0.8
2, 3a, 4
C1=C2=3.3nF,
Propagation delay from TXD to RXD
for H-L-transitions (recessive to
R1=100, no bus failures and bus
tTXRXH-L failures 1, 2, 3a, 4
1.2
dominant)
C1=100pF, C2=0, R1=100, bus
failures 3, 5, 6, 6a, 7
0.8
C1=C2=3.3nF,
R1=100, bus failures 3, 5, 6, 6a,
1.2
7
C1=100pF, C2=0, R1=100, no
bus failures and bus failures 1,
1.5
2, 3a, 4
C1=C2=3.3nF,
Propagation delay from TXD to RXD
R1=100, no bus failures and bus
2.2
for L-H-transitions (dominant to
tTXRXL-H failures 1, 2, 3a, 4
recessive)
C1=100pF, C2=0, R1=100, bus
failures 3, 5, 6, 6a, 7
0.9
C1=C2=3.3nF,
R1=100, bus failures 3, 5, 6, 7
1.4
CANH or CANL minimum dominant
time for wake-up
standby or sleep modes,
tCANHLwu VBAT=12V
8
20
Minimum change time of /WAKE for
wake up
standby or sleep modes,
tWAKEmin VBAT=12V
8
20
Disable time of permanent dominant
TXD timer
tTXDdis
normal operation mode and all
bus failures
1
2.5
2.2
µs
µs
1.5
µs
1.8
µs
1.5
µs
1.8
µs
2.0
µs
3.2
µs
1.5
µs
2.1
µs
35
µs
35
µs
4.0 ms
Low time of missing battery voltage
for setting power-on flag
Minimum hold time for go-to-sleep
command
Differemce of edge count between
CANH and CANL for detection of
failures 1, 2, 3a, 4
Differemce of edge count between
CANH and CANL for recovery of
failures 1, 2, 3a, 4
tpwon standby and sleep modes
tgo2sleep
ecfail normal operation mode
ecrec normal operation mode
0.2
1
ms
4
20
35
4
2
Datasheet Rev 1.2 Nov 2000
Page 9
www.melexis.com

Share Link: 

datasheetq.com  [ Privacy Policy ]Request Datasheet ] [ Contact Us ]