5962-9669001HYX データシートの表示（PDF） - White Electronic Designs Corporation
部品番号
コンポーネント説明
メーカー
5962-9669001HYX Datasheet PDF : 14 Pages
| |||
White Electronic Designs
WMF128K8-XXX5
ABSOLUTE MAXIMUM RATINGS (1)
Parameter
Unit
Operating Temperature
-55 to +125 °C
Supply Voltage (VCC)
-2.0 to +7.0
V
Signal Voltage Range (any pin except A9) (2) -2.0 to +7.0
V
Storage Temperature Range
Lead Temperature (soldering, 10 seconds)
-65 to +150 °C
+300
°C
Data Retention Mil Temp
10
years
Endurance (write/erase cycles) (Mil Temp)
10,000 min cycles
A9 Voltage for sector protect (VID) (3)
-2.0 to +14.0 V
NOTES:
1. Stresses above the absolute maximum rating may cause permanent damage to the
device. Extended operation at the maximum levels may degrade performance and
affect reliability.
2. Minimum DC voltage on input or I/O pins is -0.5V. During voltage transitions, inputs
may overshoot VSS to -2.0 V for periods of up to 20ns. Maximum DC voltage on
output and I/O pins is VCC + 0.5V. During voltage transitions, outputs may overshoot
to Vcc + 2.0 V for periods of up to 20ns.
3. Minimum DC input voltage on A9 pin is -0.5V. During voltage transitions, A9 may
overshoot Vss to -2V for periods of up to 20ns. Maximum DC input voltage on A9 is
+13.5V which may overshoot to 14.0 V for periods up to 20ns.
RECOMMENDED OPERATING CONDITIONS
Parameter
Supply Voltage
Input High Voltage
Input Low Voltage
Operating Temp. (Mil.)
Operating Temp. (Ind.)
A9 Voltage for Sector Protect
Symbol
VCC
VIH
VIL
TA
TA
VID
Min Max Unit
4.5
5.5
V
2.0 VCC + 0.5 V
-0.5 +0.8
V
-55 +125 °C
-40
+85
°C
11.5 12.5
V
CAPACITANCE
TA = +25°C
Parameter
Address Input capacitance
Output Enable capacitance
Write Enable capacitance
Chip Select capacitance
Data I/O capacitance
Symbol
Conditions
Max Unit
CAD VI/O = 0 V, f = 1.0 MHz 15 pF
COE VIN = 0 V, f = 1.0 MHz 15 pF
CWE VIN = 0 V, f = 1.0 MHz 15 pF
CCS VIN = 0 V, f = 1.0 MHz 15 pF
CI/O VI/O = 0 V, f = 1.0 MHz 15 pF
This parameter is guaranteed by design but not tested.
DC CHARACTERISTICS — CMOS COMPATIBLE
VCC = 5.0V, VSS = 0V, -55°C ≤ TA ≤ +125°C
Parameter
Symbol Conditions
Min
Max
Unit
Input Leakage Current
ILI
VCC = 5.5, VIN = GND to VCC
10
µA
Output Leakage Current
ILO
VCC = 5.5, VIN = GND to VCC
10
µA
VCC Active Current for Read (1)
ICC1
CS# = VIL, OE# = VIH
35
mA
VCC Active Current for Program or Erase (2)
ICC2
CS# = VIL, OE# = VIH
50
mA
VCC Standby Current
ICC3
VCC = 5.5, CS# = VIH, f = 5MHz
1.6
mA
Output Low Voltage
VOL
IOL = 8.0 mA, VCC = 4.5
0.45
V
Output High Voltage
VOH1
IOH = -2.5 mA, VCC = 4.5
0.85 x VCC
V
Output High Voltage
VOH2
IOH = -100 µA, VCC = 4.5
VCC - 0.4
V
Low VCC Lock-Out Voltage
VLKO
3.2
V
NOTES:
1. The ICC current listed includes both the DC operating current and the frequency dependent component (at 5 MHz).
The frequency component typically is less than 2 mA/MHz, with OE# at VIH.
2. ICC active while Embedded Algorithm (program or erase) is in progress.
3. DC test conditions: VIL = 0.3V, VIH = VCC - 0.3V
AC TEST CIRCUIT
I OL
Current Source
D.U.T.
Ceff = 50 pf
I OH
Current Source
VZ 1.5V
(Bipolar Supply)
AC TEST CONDITIONS
Parameter
Typ
Unit
Input Pulse Levels
VIL = 0, VIH = 3.0 V
Input Rise and Fall
5
ns
Input and Output Reference Level
1.5
V
Output Timing Reference Level
1.5
V
Notes:
VZ is programmable from -2V to +7V.
IOL & IOH programmable from 0 to 16mA.
Tester Impedance Z0 = 75 Ω.
VZ is typically the midpoint of VOH and VOL.
IOL & IOH are adjusted to simulate a typical resistive load circuit.
ATE tester includes jig capacitance.
White Electronic Designs Corp. reserves the right to change products or specifications without notice.
April 2001
Rev. 5
2
White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com
Share Link: 