HA-2539_03 データシートの表示（PDF） - Intersil
部品番号
コンポーネント説明
メーカー
HA-2539_03 Datasheet PDF : 10 Pages
| |||
HA-2539
Absolute Maximum Ratings
Supply Voltage Between V+ and V- Terminals . . . . . . . . . . . . . 35V
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6V
Peak Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50mA
Continuous Output Current . . . . . . . . . . . . . . . . . . . . . . . 33mARMS
Operating Conditions
Temperature Range
HA-2539-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to 75oC
Thermal Information
Thermal Resistance (Typical, Note 2)
θJA (oC/W) θJC (oC/W)
PDIP Package . . . . . . . . . . . . . . . . . . .
95
N/A
Maximum Internal Quiescent Power Dissipation (Note 1)
Maximum Junction Temperature (Plastic Package) . . . . . . . .150oC
Maximum Storage Temperature Range . . . . . . . . . -65oC to 150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. Maximum power dissipation with load conditions must be designed to maintain the maximum junction temperature below 150oC for the plastic
package. By using Application Note AN556 on Safe Operating Area equations, along with the thermal resistances, proper load conditions can
be determined. Heat sinking is recommended above 75oC.
2. θJA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications VSUPPLY = ±15V, RL = 1kW, CL < 10pF, Unless Otherwise Specified
PARAMETER
TEMP.
(oC)
MIN
TYP
INPUT CHARACTERISTICS
Offset Voltage
25
-
8
Full
-
13
Average Offset Voltage Drift
Full
-
20
Bias Current
25
-
5
Full
-
-
Offset Current
25
-
1
Full
-
-
Input Resistance
25
-
10
Input Capacitance
25
-
1
Common Mode Range
Full
±10.0
-
Input Current Noise
(f = 1kHz, RSOURCE = 0Ω)
Input Voltage Noise
(f = 1kHz, RSOURCE = 0Ω)
TRANSFER CHARACTERISTICS
25
-
6
25
-
6
Large Signal Voltage Gain
(Note 3)
25
10
15
Full
5
-
Common Mode Rejection Ratio
(Note 4)
Full
60
72
Minimum Stable Gain
25
10
-
Gain Bandwidth (Notes 5, 6)
25
-
600
MAX
15
20
-
20
25
6
8
-
-
-
-
-
UNITS
mV
mV
µV/oC
µA
µA
µA
µA
kΩ
pF
V
pA/√Hz
nV/√Hz
-
kV/V
--
kV/V
-
dB
-
V/V
-
MHz
2
Share Link: 