ILC7010C5-36 データシートの表示（PDF） - Impala Linear Corporation

部品番号

コンポーネント説明

メーカー

ILC7010C5-36

80mA SC70 Ultra Low Noise CMOS RF-LDO™ Regulator

Impala Linear Corporation 

80mA SC70 Ultra Low Noise CMOS RF-LDO™ Regulator

Preliminary

ELECTRICAL CHARACTERISTICS ILC7010

Unless otherwise specified, all limits are at TA=25°C, VIN = VOUT(NOM) + 1v, IOUT = 1mA, COUT = 1µF, VON/OFF = 2V

Parameter

Input Voltage Range

Output Voltage Accuracy

Line Regulation

Dropout Voltage (Note 3)

Ground Pin Current

Shutdown (OFF) Current

ON/OFF Input Voltage

ON/OFF Pin Input Current

(Note 5)

Peak Output Current

(Note 4)

Output Noise Voltage

(RMS)

Ripple Rejection

Dynamic Line Regulation

Dynamic Load Regulation

Short Circuit Current

Resistance Shutdown

Discharge

Symbol

VIN

∆VOUT/(VOUT*∆VIN)

VIN VOUT

IGND

ION/OFF

VON/OFF

IIN ON/OFF

IIN (peak)

eN

∆VOUT/∆VIN

∆VOUT (line)

∆VOUT(load)

ISC

Conditions

VOUT (NOM +1V < 8V)

IOUT = 10µA

IOUT = 10mA

IOUT = 20mA

IOUT = 80mA

IOUT = 0mA

IOUT = 10mA

IOUT = 80mA

ION/OFF = 0V

High = Regulator On

Low = Regulator Off

VON/OFF 0.6V Regulator OFF

VON/OFF 2V Regulator ON

VOUT > 0.95VOUT (NOM), tpw = 2ms

Typ

2.5-8

±1

0.007

0.1

50

70

235

66

67

90

0.1

1.5-2.0

0.6

0.3

1

Units

V

%

%/V

mV

µA

µA

V

µA

100-120 mA

BW = 300Hz to 50kHz, CIN = 1µF

CNOISE = 0.01µF, COUT = 2.2µF,

IOUT = 10mA

COUT = 4.7µF

IOUT = 100mA

Freq = 1kHz

Freq = 10kHz

Freq = 1MHz

VIN: VOUT (NOM) + 1V to VOUT

(NOM) + 2V, tr/tf = 2µs; IOUT = 80mA

IOUT: 1mA to 80mA; tr < 5mS

VOUT = 0V

TBD

70

50

65

14

40

200

1.5

µVRMS

dB

mV

mV

mA

kΩ

Note 1: Absolute maximum ratings indicate limits which when exceeded may result in damage to the component. Electrical specifications do not apply when operating the

device outside of its rated operating conditions.

Note 2: Specified Min/Max limits are production tested or guaranteed through correlation based on statistical control methods. Measurements are taken at constant junction

temperature as close to ambient as possible using low duty pulse testing.

Note 3: Dropout voltage is defined as the input to output differential voltage at which the output voltage drops 2% below the nominal value measured with a 1V differential.

Note 4: Guaranteed by design

Note 5: The device’s shutdown pin includes a 2MΩ internal pull down resistor connected to ground.

Impala Linear Corporation

ILC7010 1.3

(408) 574-3939 www.impalalinear.com

August 2000 3

Share Link: