CMV1036 データシートの表示（PDF） - California Micro Devices Corp
部品番号
コンポーネント説明
メーカー
CMV1036 Datasheet PDF : 12 Pages
| |||
CALIFORNIA MICRO DEVICES
CMV1036
the breadboard and the production printed circuit
board, we favor the use of a "gimmick" , a technique
perfected by TV technicians in the 1950’s. A gimmick
is made by taking two lengths (typically about a foot)
of small gauge wire such as AWG 24, twisting them
together, and then after baring all ends soldering the
gimmick across RF. With the circuit operating, CF is
"adjusted" by clipping short lengths of the gimmick off
until the compensation is nominal. Then simply
remove the gimmick, take it to an impedance bridge,
and select the capacitor accordingly.
Figure 2.
4. Capacitive Load Considerations
The CMV1036 is capable of driving capacitate loads in
excess of 100pF without oscillation. However, signifi-
cant peaking will result. Probably the easiest way
minimize this problem is to use an isolation resistor as
shown in Figure 3.
Figure 3
5. Power Supply Decoupling
The CMV1036 is not prone to oscillation without the
use of power supply decoupling capacitors, however to
minimize hum and noise pick-up, it is recommended
that the rails be bypassed with 0.01µF capacitors.
6. Turn On and Turn Off (Shut Down)
Characteristics
The turn off delay (Disable Response), tOFF, is defined
as the time between the shut down signal crossing the
disable threshold (typically V+ - 1 volt) and the time for
the amplifier’s output to come within 10% of zero. It is
largely governed by a propagation delay within the
CMV1036 of few hundred nanoseconds followed by an
exponential decay determined by the load resistance
in parallel with the load capacitance.
The turn on delay (Enable Response), tON, is defined
as the time between the shutdown signal crossing the
threshold and the time the output reaches to within
10% of its final value. tON is largely independent of
supply voltage and input level.
7. Typical Applications
Illustrated in Figure 4 is a Sample and Hold Amplifier
capable of operating from a single rail, but it will work
equally well with split rails The circuit will accommo-
date input voltages (common mode) from zero volts to
V+ - 1 volt. The Shut Down feature of the CMV1036 is
used to disable A whose output acts like a very high
1
impedance in this mode. The high slew rate of the
CMV1036 and large output current minimize Acquisi-
tion Time. A2 presents a very high input impedance
and very low bias current. A Logic 1, a voltage > V+ –
1 volt will put the circuit into "Sample" mode. A Logic
"0" will put the circuit in "Hold" mode. For the values
shown, Acquisition Time to 0.1% is typically 10 mS for
a zero to 4 volt input, the hold step is typically 400µV,
and the droop rate at 85°C is 0.1µV/µS. Overall
accuracy is better than 0.01%. For minimum droop, C1
should be of polystyrene construction.
7. Typical Applications
Illustrated in Figure 4 is a Sample and Hold Amplifier
capable of operating from a single rail, but it will work
equally well with split rails The circuit will accommo-
date input voltages (common mode) from zero volts to
V+ – 1 volt. The Shut Down feature of the CMV1036 is
used to disable A1 whose output acts like a very high
impedance in this mode. The high slew rate of the
CMV1036 and large output current minimize Acquisi-
tion Time. A2 presents a very high input impedance
and very low bias current A Logic "1", a voltage > V+
– 1 volt will put the circuit into Sample mode. A Logic
"0" will put the circuit in "Hold" mode. For the values
shown, Acquisition Time to 0.1% is typically 10µS for
a zero to 4 volt input, the hold step is typically 400 µV,
and the droop rate at 85°C is 0.1µV/µS. Overall
accuracy is better than 0.01%. For minimum droop, C1
should be of polystyrene construction.
© 2000 California Micro Devices Corp. All rights reserved.
5/00
215 Topaz Street, Milpitas, California 95035 Tel: (408) 263-3214 Fax: (408) 263-7846 www.calmicro.com
11
Share Link: 