MAX6874 データシートの表示（PDF） - Maxim Integrated
部品番号
コンポーネント説明
メーカー
MAX6874 Datasheet PDF : 40 Pages
| |||
EEPROM-Programmable, Hex/Quad,
Power-Supply Sequencers/Supervisors
ABSOLUTE MAXIMUM RATINGS
(All voltages referenced to GND)
IN2–IN6, ABP, SDA, SCL, A0, A1,
GPI1–GPI4, MR, MARGIN, PO5–PO8
(MAX6874), PO3–PO5 (MAX6875)...................-0.3V to +6V
IN1, PO1–PO4 (MAX6874), PO1–PO2 (MAX6875)...-0.3V to +14V
DBP ..........................................................................-0.3V to +3V
Input/Output Current (all pins)..........................................±20mA
Continuous Power Dissipation (TA = +70°C)
32-Pin 7mm x 7mm Thin QFN
(derate 33.3mW/°C above +70°C) .............................2667mW
Operating Temperature Range ...........................-40°C to +85°C
Maximum Junction Temperature .....................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VIN1 = +6.5V to +13.2V, VIN2–VIN6 = +2.7V to +5.5V, GPI_ = GND, MARGIN = MR = DBP, TA = -40°C to +85°C, unless otherwise
noted. Typical values are at TA = +25°C.) (Notes 1, 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP MAX UNITS
Operating Voltage Range
(Note 3)
VIN1
Voltage on IN1 to ensure the device is fully
operational, IN3–IN6 = GND
4.0
VIN3 to Voltage on any one of IN3–IN5 to ensure the
2.7
VIN5 device is fully operational, IN1 = GND
13.2
V
5.5
IN1 Supply Voltage
(Note 3)
VIN1P
Minimum voltage on IN1 to guarantee that the
device is powered through IN1
6.5
V
Undervoltage Lockout
VUVLO
Minimum voltage on one of IN3–IN5 to
guarantee the device is EEPROM configured.
2.5
V
Supply Current
VIN1 = +13.2V, IN2–IN6 = GND, no load
ICC Writing to configuration registers or EEPROM,
no load
1.2
1.5
mA
1.3
2
mA
Threshold Range
Threshold Accuracy
Threshold Hysteresis
Reset Threshold Temperature
Coefficient
VIN1 (50mV increments)
2.5
VIN1 (25mV increments)
1.250
VTH
VIN2 (50mV increments)
VIN2 (25mV increments)
2.50
1.250
VIN3–VIN6 (20mV increments)
1.0
VIN3–VIN6 (10mV increments)
0.50
IN1–IN6, VIN_ falling
TA = +25°C
-1.0
TA = -40°C to +85°C -1.5
13.2
7.625
5.5
V
3.05
5.5
3.05
+1.0
%
+1.5
VTH-HYST
0.3
% VTH
∆VTH/°C
10
ppm/
°C
Threshold-Voltage Differential
Nonlinearity
VTH DNL
-1
+1
LSB
2 _______________________________________________________________________________________
Share Link: 