MBM29LV017-12PTR データシートの表示（PDF） - Fujitsu

部品番号

コンポーネント説明

メーカー

MBM29LV017-12PTR

CMOS 16M (2M × 8) BIT

Fujitsu 

MBM29LV017-80/-90/-12

s GENERAL DESCRIPTION

The MBM29LV017 is a 16M-bit, 3.0 V-only Flash memory organized as 2M bytes of 8 bits each. The 2M bytes

of data is divided into 32 sectors of 64K bytes of flexible erase capability. The 8 bits of data will appear on DQ0

to DQ7. The MBM29LV017 is offered in a 40-pin TSOP (I), 48-ball FBGA packages. The device is designed to

be programmed in-system with the standard system 3.0 V VCC supply. 12.0 V VPP and 5.0 V VCC are not required

for write or erase operations. The device can also be reprogrammed in standard EPROM programmers.

The standard MBM29LV017 offers access times of 80 ns and 120 ns, allowing operation of high-speed

microprocessors without wait states. To eliminate bus contention the device has separate chip enable (CE), write

enable (WE), and output enable (OE) controls.

The MBM29LV017 is pin and command set compatible with JEDEC standard E2PROMs. Commands are written

to the command register using standard microprocessor write timings. Register contents serve as input to an

internal state-machine which controls the erase and programming circuitry. Write cycles also internally latch

addresses and data needed for the programming and erase operations. Reading data out of the device is similar

to reading from 5.0 V and 12.0 V Flash or EPROM devices.

The MBM29LV017 is programmed by executing the program command sequence. This will invoke the Embedded

Program Algorithm which is an internal algorithm that automatically times the program pulse widths and verifies

proper cell margins. Typically, each sector can be programmed and verified in about 0.5 seconds. Erase is

accomplished by executing the erase command sequence. This will invoke the Embedded Erase Algorithm which

is an internal algorithm that automatically preprograms the array if it is not already programmed before executing

the erase operation. During erase, the device automatically times the erase pulse widths and verifies proper cell

margins.

Any individual sector is typically erased and verified in 1.0 second. (If already preprogrammed.)

The device also features a sector erase architecture. The sector mode allows each sector to be erased and

reprogrammed without affecting other sectors. The MBM29LV017 is erased when shipped from the factory.

The MBM29F017A device also features hardware sector group protection. This feature will disable both program

and erase operations in any combination of eight sectior groups of memory. A sector group consists of four

adjacect sectors grouped in the following pattern: sectors 0-3, 4-7, 8-11, 12-15, 16-19, 20-23, 24-27, and 28-31.

Fujitsu has implemented an Erase Suspend feature that enables the user to put erase on hold for any period of

time to read data from or program data to a mom-busy sector. Thus, true background erase can be achieved.

The device features single 3.0 V power supply operation for both read and write functions. Internally generated

and regulated voltages are provided for the program and erase operations. A low VCC detector automatically

inhibits write operations on the loss of power. The end of program or erase is detected by Data Polling of DQ7,

by the Toggle Bit feature on DQ6, or the RY/BY output pin. Once the end of a program or erase cycle has been

comleted, the device internally resets to the read mode.

The MBM29LV017 also has a hardware RESET pin. When this pin is driven low, execution of any Embedded

Program Algorithm or Embedded Erase Algorithm is terminated. The internal state machine is then reset to the

read mode. The RESET pin may be tied to the system reset circuitry. Therefore, if a system reset occurs during

the Embedded Program Algorithm or Embedded Erase Algorithm, the device is automatically reset to the read

mode and will have erroneous data stored in the address locations being programmed or erased. These locations

need re-writing after the Reset. Resetting the device enables the system’s microprocessor to read the boot-up

firmware from the Flash memory.

Fujitsu’s Flash technology combines years of Flash memory manufacturing experience to produce the highest

levels of quality, reliability, and cost effectiveness. The MBM29LV017 memory electrically erases all bits within

a sector simultaneously via Fowler-Nordhiem tunneling. The bytes are programmed one byte at a time using

the EPROM programming mechanism of hot electron injection.

3

Share Link: