LT1195(Rev0) データシートの表示（PDF） - Linear Technology
部品番号
コンポーネント説明
メーカー
LT1195 Datasheet PDF : 12 Pages
| |||
LT1195
+–5V ELECTRICAL CHARACTERISTICS 0°C ≤ TA ≤ 70°C
VS = ±5V, pin 5 open circuit, unless otherwise noted.
SYMBOL
VOS
∆VOS/∆T
IOS
IB
CMRR
PSRR
AVOL
VOUT
IS
IS/D
PARAMETER
Input Offset Voltage
Input VOS Drift
Input Offset Current
Input Bias Current
Common-Mode Rejection Ratio
Power Supply Rejection Ratio
Large-Signal Voltage Gain
Output Voltage Swing
Supply Current
Shutdown Supply Current
Shutdown Pin Current
CONDITIONS
J8, N8 Package
S8 Package
VCM = –2.5V to 3.5V
VS = ±2.375V to ±5V
RL = 1k, VOUT = ±3V
RL = 150Ω, VOUT = ±3V
RL = 1k
Pin 5 at V –, (Note 8)
Pin 5 at V –
LT1195C
MIN TYP MAX
3.0 10.0
3.0 15.0
12
0.2
1.7
±0.5 ±2.5
60
85
60
90
2.0
7.5
0.3
1.5
±3.7 ±3.9
12
17
0.9
2.0
5
25
UNITS
mV
mV
µV/°C
µA
µA
dB
dB
V/mV
V/mV
V
mA
mA
µA
5V ELECTRICAL CHARACTERISTICS 0°C ≤ TA ≤ 70°C
VS+ = 5V, VS– = OV, VCM = 2.5V, pin 5 open circuit, unless otherwise noted.
SYMBOL
VOS
∆VOS/∆T
IOS
IB
CMRR
VOUT
PARAMETER
Input Offset Voltage
Input VOS Drift
Input Offset Current
Input Bias Current
Input Voltage Range
Common-Mode Rejection Ratio
Output Voltage Swing
IS
Supply Current
Shutdown Supply Current
IS/D
Shutdown Pin Current
CONDITIONS
J8, N8 Package
S8 Package
(Note 3)
VCM = 2V to 3.5V
RL = 150Ω to Ground
Pin 5 at V–, (Note 8)
Pin 5 at V–
VOUT High
VOUT Low
LT1195C
MIN TYP MAX
1.0
10.0
1.0
15.0
15
0.2
1.7
±0.5 ±2.5
2.0
3.5
60
85
3.5
3.75
0.15
0.4
12
16
0.9
2.0
5
25
UNITS
mV
mV
µV/°C
µA
µA
V
dB
V
V
mA
mA
µA
Note 1: A heat sink may be required to keep the junction temperature
below absolute maximum when the output is shorted continuously.
Note 2: TJ is calculated from the ambient temperature TA and power
dissipation PD according to the following formats:
LT1195MJ8, LT1195CJ8: TJ = TA + (PD × 100°C/ W)
LT1195N:
TJ = TA + (PD × 100°C/ W)
LT1195CS:
TJ = TA + (PD × 150°C/ W)
Note 3: Exceeding the input common-mode range may cause the output
to invert.
Note 4: Slew rate is measured between ±1V on the output, with ±3V
input step.
Note 5: Full power bandwidth is calculated from the slew rate
measurement: FPBW = SR/2πVP.
Note 6: Settling time measurement techniques are shown in “Take the
Guesswork Out of Settling Time Measurements,” EDN, September 19, 1985.
Note 7: NTSC (3.58MHz). For RL = 1k, Diff AV = 0.3%, Diff Ph = 0.35°.
Note 8: See Applications Information section for shutdown at elevated
temperatures. Do not operate the shutdown above TJ > 125°C.
Note 9: AC parameters are 100% tested on the ceramic and plastic DIP
packaged parts (J8 and N8 suffix) and are sample tested on every lot of
the SO packaged parts (S8 suffix).
Note 10: Do not operate at AV < 2 for TA < 0°C.
4
Share Link: 