MAX974CSE(1995) データシートの表示（PDF） - Maxim Integrated

部品番号

コンポーネント説明

メーカー

MAX974CSE
(Rev.:1995)

Ultra-Low-Power, Open-Drain, Single/Dual-Supply Comparators

Maxim Integrated 

Ultra-Low-Power, Open-Drain,

Single/Dual-Supply Comparators

ABSOLUTE MAXIMUM RATINGS

V+ to V-, V+ to GND, GND to V-................................-0.3V, +12V

Inputs

Current: IN_+, IN_-, HYST..............................................20mA

Voltage: IN_+, IN_-, HYST ...............(V+ + 0.3V) to (V- - 0.3V)

Outputs

Current: REF...................................................................20mA

OUT_ ................................................................50mA

Voltage: REF ....................................(V+ + 0.3V) to (V- - 0.3V)

OUT_ (MAX9_1/9_4) ...............+12V to (GND - 0.3V)

(MAX9_2/9_3) ....................+12V to (V- - 0.3V)

OUT_ Short-Circuit Duration ..................................Continuous

Continuous Power Dissipation (TA = +70°C)

8-Pin Plastic DIP (derate 9.09mW/°C above +70°C) ...727mW

8-Pin SO (derate 5.88mW/°C above +70°C)................471mW

8-Pin µMAX (derate 4.1mW/°C above +70°C) .............330mW

8-Pin CERDIP (derate 8.00mW/°C above +70°C)........640mW

16-Pin Plastic DIP (derate 10.53mW/°C above +70°C)..842mW

16-Pin SO (derate 8.70mW/°C above +70°C) ................696mW

16-Pin CERDIP (derate 10.00mW/°C above +70°C) ......800mW

Operating Temperature Ranges

MAX97_C_ _/MAX98_C_ _ ..................................0°C to +70°C

MAX97_E_ _/MAX98_E_ _ ...............................-40°C to +85°C

MAX97_MJ_/MAX98_MJ_ .............................-55°C to +125°C

Storage Temperature Range .............................-65°C to +150°C

Lead Temperature (soldering, 10sec) .............................+300°C

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional

operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to

absolute maximum rating conditions for extended periods may affect device reliability.

ELECTRICAL CHARACTERISTICS: 5V OPERATION

(V+ = 5V, V- = GND = 0V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.)

PARAMETER

CONDITIONS

MIN

TYP

MAX UNITS

POWER REQUIREMENTS

Supply Voltage Range

Output Voltage Range

Supply Current

COMPARATOR

Input Offset Voltage

Input Leakage Current (IN-, IN+)

Input Leakage Current (HYST)

Input Common-Mode Voltage Range

Common-Mode Rejection Ratio

Power-Supply Rejection Ratio

Voltage Noise

Hysteresis Input Voltage Range

Response Time

(high-to-low transition)

(Note 1)

2.5

11

0

11

TA = +25°C

MAX9_1,

HYST = REF

C/E temp. ranges

M temp. range

2.5

3.2

4

5

TA = +25°C

2.5

3.2

MAX972 C/E temp. ranges

4

IN+ = IN- + 100mV

MAX982/

MAX9_3,

HYST = REF

M temp. range

TA = +25°C

C/E temp. ranges

M temp. range

5

3.1

4.5

6

7.5

MAX9_4

TA = +25°C

C/E temp. ranges

5.5

6.5

8.5

M temp. range

11

VCM = 2.5V

IN+ = IN- = 2.5V

MAX9_1/MAX982/MAX9_3

V- to (V+ - 1.3V)

V+ = 2.5V to 11V

100Hz to 100kHz

MAX9_1/MAX982/MAX9_3

TA = +25°C, 100pF load,

1MΩ pull-up to V+

C/E temp. ranges

±0.01

M temp. range

±0.02

V-

0.1

0.1

20

REF - 0.05

Overdrive = 10mV

12

Overdrive = 100mV

4

±10

±5

±40

V+ - 1.3

1.0

1.0

REF

V

V

µA

mV

nA

nA

V

mV/V

mV/V

µVRMS

V

µs

Response Time

(low-to-high transition) (Note 2)

TA = +25°C, 100pF load, 1MΩ pull-up to V+

300

µs

2 _______________________________________________________________________________________

Share Link: