ICM7243 データシートの表示（PDF） - Renesas Electronics

部品番号

コンポーネント説明

メーカー

ICM7243

8-Character, Microprocessor-Compatible, LED Display Decoder Driver

Renesas Electronics 

DATASHEET

ICM7243

8-Character, Microprocessor-Compatible, LED Display Decoder Driver

FN3162

Rev 5.00

October 2, 2015

The ICM7243 is an 8-character, alphanumeric display driver

and controller which provides all the circuitry required to

interface a microprocessor or digital system to a 14-segment

or 16-segment display. It is primarily intended for use in

microprocessor systems, where it minimizes hardware and

software overhead. Incorporated on-chip are a 64-character

ASClI decoder, 8x6 memory, high power character and

segment drivers, and the multiplex scan circuitry.

6-bit ASCll data to be displayed is written into the memory

directly from the microprocessor data bus. Data location

depends upon the selection of either Sequential

(MODE = 1) or Random access mode (MODE = 0). In the

Sequential Access mode the first entry is stored in the

lowest location and displayed in the “left-most” character

position. Each subsequent entry is automatically stored in

the next higher location and displayed to the immediate

“right” of the previous entry. A DISPlay FULL signal is

provided after 8 entries; this signal can be used for

cascading devices together. A CLeaR pin is provided to

clear the memory and reset the location counter. The

Random Access mode allows the processor to select the

memory address and display digit for each input word.

The character multiplex scan runs whenever data is not

being entered. It scans the memory and CHARacter drivers,

and ensures that the decoding from memory to display is

done in the proper sequence. Intercharacter blanking is

provided to avoid display ghosting

Features

• 14-Segment and 16-Segment Fonts with Decimal Point

• Mask Programmable for Other Font-Sets Up to 64

Characters

• Microprocessor Compatible

• Directly Drives LED Common Cathode Displays

• Cascadable Without Additional Hardware

• Standby Feature Turns Display Off; Puts Chip in Low

Power Mode

• Sequential Entry or Random Entry of Data Into Display

• Single +5V Operation

• Character and Segment Drivers, All MUX Scan Circuitry,

8x6 Static Memory and 64-Character ASCll Font

Generator Included On-Chip

• Pb-Free Available (RoHS Compliant)

Ordering Information

PART

NUMBER

PART

MARKING

TEMP. RANGE

(°C)

PACKAGE

(Pb-Free)

PKG.

DWG. #

ICM7243BlPL** (No longer available or

supported)

ICM7243BlPL

-25 to +85

40 Ld PDIP

E40.6

ICM7243BlPLZ ** (Note)

ICM7243BlPLZ

-25 to +85

40 Ld PDIP

E40.6

ICM7243AIM44Z* (Note) (No longer

available, recommended replacement:

ICM7244AIM44Z, ICM7244AIM44ZT)

ICM7243 AIM44Z

-25 to +85

44 Ld MQFP

Q44.10x10

ICM7243AIPLZ** (Note) (No longer available ICM7243AIPLZ

or supported)

-20 to +85

40 Ld PDIP

E40.6

*Add “-T” suffix for tape and reel. Please refer to TB347 for details on reel specifications.

**Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications.

NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100%

matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil

Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020

FN3162 Rev 5.00

October 2, 2015

Page 1 of 17

Share Link: