TEA1062A データシートの表示（PDF） - Contek Microelectronics

部品番号

コンポーネント説明

メーカー

TEA1062A

LOW VOLTAGE TELEPHONE TRANSMISSION CIRCUIT WITH DIALLER INTERFACE

Contek Microelectronics 

TEA1062/1062A LINEARINTEGRATED CIRCUIT

Automatic gain control input(AGC)

Automatic line loss compensation is achieved by

connecting a resistor(R6) between AGC and VEE. The

automatic gain control varies the gain of the

microphone amplifier and the receiving amplifier in

accordance with the DC line current. The control range

is 5.8dB which corresponds to a line length of 5km for a

0.5mm diameter twisted pair copper cable with a DC

resistance of 176 W/km and average attenuation of

1.2dB/km. Resistor R6 should be chosen inaccordance

with the exchange supply voltage and its feeding bridge

resistance(see Fig.12 and Table 1). The ratio of start

and stop currents of the AGC curve is independent of

the value of R6. If no automatic line loss compensation

is required the AGC may be left open-circuit. The

amplifier, in this condition, will give their maximum

specified gain.

Side-tone suppression

The anti- sidetone network, R1//Z line, R2, R3, R8, R9

and Zbal,(see Fig.4) suppresses the transmitted signal

in the earpiece. Compensation is maximum when the

following conditions are fulfilled:

(a) R9*R2=

R1[R3+(R8//Zbal)];

(b) [

Zbal/(Zbal+R8)]=[Zline/(Zline+R1)];

If fixed values are chosen for R1, R2, R3 and R9 then

condition(a) will always be fullfilled when R8/Z ball R3.

To obtain optimum side-tone suppression condition(b)

has to be fulfilled which results in:

Zbal=(R8/R1) Zline=k*Zline where k is a scale factor;

K=(R8/R1).

The scale factor (k), dependent on the value of R8, is

chosen to meet following criteria:

(a) Compatibility with a standard capacitor from the

E6 or E12 range for Zbal,

(b) Zbal//R8 R3 fulfilling condition (a) and thus

ensuring correct anti-sidetone bridge operation,

(c) Zbal+R8 R9to avoid influencing the trans-

mitter gain.

In practice Zline varies considerably with the type and

length. The value chosen for Zbal should therefore be

for an average line length thus giving optimum setting

for short or long lines.

1mA) This means that more sets can be operated in

parallel with DC line voltages (excluding the polarity

guard) down to an absolute minimum voltage of 1.6V.

With line currents below 9mA the circuit has limited

sending and receiving levels. The internal reference

voltage can be adjusted by means of an external

resistor(RVA). This resistor when connected between

LN and REG will decrease the internal reference

voltage and when connected between REG and SLPE

will increase the internal reference voltage. Current(Ip)

available from VCC for peripheral circuits depends on

the external components used. Fig.9 shows this current

for VCC > 2.2V. If MUTE is LOW (1062 is HIGH )when

the receiving amplifier is driven the available current is

further reduced. Current availability can be increased

by connecting the supply IC(1081) in parallel with R1,

as shown in Fig.16(c), or, by increasing the DC line

voltage by means of an external resistor( RVA)

connected between REG and SLPE.

Example

The balance impedance Zbal at which the optimum

suppression is present can be calculated by: Suppose

Zline = 210 W+(1265W//140nF) representing a 5km line

of 0.5 mm diameter, copper, twisted pair cable matched

to 600 W(176W/km;38nF/km). When k=0.64 then

R8=390W,Zbal=130W+(820W//220nF). At line currents

below 9mA the internal reference voltage is

automatically adjusted to a lower value(typically 1.6V at

Contek Microelectronics Co.,Ltd.

7

CONTEK

http://www.contek-ic.com E-mail:sales@contek-ic.com

Share Link: