INTEL82801E データシートの表示（PDF） - Intel

部品番号

コンポーネント説明

メーカー

INTEL82801E

Intel® 82801E Communications I/O Controller Hub (C-ICH)

Intel 

Intel® 82801E C-ICH

Table 6. 82801E C-ICH Signal Description (Sheet 2 of 11)

Signal

C/BE[3:0]#

CLK14

CLK48

CLK66

(HLCLK)

CPUPWRGD

CPUSLP#

DEVSEL#

EE0_CS

EE1_CS

EE0_DIN

EE1_DIN

EE0_DOUT

EE1_DOUT

EE0_SHCLK

EE1_SHCLK

Type

I/O

I

I

I

OD

O

I/O

O

I

O

O

Description

Bus Command and Byte Enables: The command and byte enable signals

are multiplexed on the same PCI pins. During the address phase of a

transaction, C/BE[3:0]# define the bus command. During the data phase,

C/BE[3:0]# define the Byte Enables.

C/BE[3:0]#

0000

0001

0010

0011

0110

0111

Command Type

Interrupt Acknowledge

Special Cycle

I/O Read

I/O Write

Memory Read

Memory Write

1010

1011

1100

Configuration Read

Configuration Write

Memory Read Multiple

1101

1110

1111

DAC Mode Address to be latched (target only)

Memory Read Line

Memory Write and Invalidate

All command encodings not shown are reserved. The 82801E C-ICH does

not decode reserved values, and therefore will not respond when a PCI

master generates a cycle using one of the reserved values.

As a target, the 82801E C-ICH can support DAC mode addressing for 44 bits.

Oscillator Clock: CLK14 is used for 8254 timers and runs at 14.31818 MHz.

48 MHz Clock: CLK48 is used to for the USB controller and runs at 48 MHz.

66 MHz Clock (HLCLK): CLK66 is used for the hub interface and runs at

66 MHz.

Processor Power Good: This signal should be connected to the processor’s

PWRGOOD input. This is an open-drain output signal (external pull-up

resistor required) that represents a logical AND of the 82801E C-ICH’s

PWROK and VRMPWRGD signals.

Processor Sleep: This signal puts the processor into a state that saves

substantial power compared to Stop-Grant state. However, during that time,

no snoops occur.

NOTE: The 82801E C-ICH does not support Sleep states. This signal must

be pulled up through an 8.2 KΩ resistor to 3.3 V.

Device Select: The 82801E C-ICH asserts DEVSEL# to claim a PCI

transaction. As an output, the 82801E C-ICH asserts DEVSEL# when a PCI

master peripheral attempts an access to an internal 82801E C-ICH address

or an address destined for the hub interface (main memory or AGP). As an

input, DEVSEL# indicates the response to an 82801E C-ICH-initiated

transaction on the PCI bus. DEVSEL# is tri-stated from the leading edge of

PCIRST#. DEVSEL# remains tri-stated by the 82801E C-ICH until driven by a

target device.

EEPROM Chip Select: These signals are chip-select signals to the

EEPROMs.

EEPROM Data In: These signals transfer data from the EEPROMs to the

82801E C-ICH. These signals have an integrated pull-up resistor.

EEPROM Data Out: These signals transfer data from the 82801E C-ICH to

the EEPROMs.

EEPROM Shift Clock: These signals are the serial shift clock output to the

EEPROMs.

26

Advance Information Datasheet

Share Link: