DatasheetQ Logo
Electronic component search and free download site. Transistors,MosFET ,Diode,Integrated circuits

TS391 データシートの表示(PDF) - STMicroelectronics

部品番号
コンポーネント説明
メーカー
TS391
ST-Microelectronics
STMicroelectronics ST-Microelectronics
TS391 Datasheet PDF : 14 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
Electrical characteristics
TS391, TS391A
4
Electrical characteristics
Symbol
Vio
Iib
Iio
AVD
ICC
Vid
Isink
VOL
IOH
tre
trel
Table 3: VCC+ = 5 V, VCC- = 0 V, Tamb = 25 °C (unless otherwise specified)
Parameter and test conditions
Min. Typ. Max.
TS391
TS391A
TS391
TS391A
Input offset voltage (1)
Input offset voltage, Tmin ≤ Tamb ≤ Tmax
Input offset voltage (1)
Input offset voltage, Tmin ≤ Tamb ≤ Tmax
Input bias current (2)
Input bias current, Tmin ≤ Tamb ≤ Tmax
Input bias current (2)
Input bias current, Tmin ≤ Tamb ≤ Tmax
1
5
9
1 1.5
2
25 250
400
25 150
250
Input offset current
5
50
Input offset current, Tmin Tamb Tmax
150
Large signal voltage gain, (VCC+) = 15 V, RL=15 kΩ, Vο = 1 tο 11 V
Supply current (VCC +) = 5 V, no load
Supply current (VCC +) = 30 V, no load
Differential input voltage (3)
Output sink current, Vid = -1 V, Vo = 1.5 V
Low level output voltage, Vid = 1 V, VCC+ = Vo = 30 V
50 200
0.2 0.5
0.5 1.25
VCC+
6 16
250 400
700
High level output current, Vid = 1 V, VCC+ = Vo = 30 V
Small signal response time, RL = 5.1 kΩ to (VCC+) (4)
Large signal response time, Vi = TTL, Vref = 1.4 V, RL = 5.1 kΩ to VCC+
0.1
1
1.3
300
Unit
mV
nA
V/mV
mA
V
mA
mV
nA
µA
µs
ns
Notes:
(1)At the output switch point, Vo ≈ 1.4 V, RS = 0 Ω with (VCC+) from 5 V to 30 V, and over the full input common-mode range
(0 V to (VCC+) 1.5 V).
(2)The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of
the state of the output, so there is no load charge on the reference of input lines.
(3)Positive excursions of the input voltage may exceed the power supply level. As long as the other voltage remains within the
common-mode range, the comparator will provide a proper output state. The low input voltage state must not be less than
0.3 V (or 0.3 V below the negative power supply, if used)
(4)The response time specified is for a 100 mV input step with 5 mV overdrive. For larger overdrive signals, 300 ns can be
obtained.
6/14
DocID6324 Rev 8

Share Link: 

datasheetq.com  [ Privacy Policy ]Request Datasheet ] [ Contact Us ]