BA7780 データシートの表示（PDF） - ROHM Semiconductor
部品番号
コンポーネント説明
メーカー
BA7780 Datasheet PDF : 10 Pages
| |||
Video ICs
BA7780KV
•Electrical characteristics
Measurement conditions
Unless otherwise noted, the following conditions apply:
Ta = 25°C, VCC3.3V, external supply voltage (pin 24) =
4.75V, pin 19 = “H” or open, pin 26 = 1 / 2VCC, pin 51 =
0.58 × pin 4, pin 27 = 0.733 × pin 4, pin 28 = 0.80 × pin 4,
pin 29 = 2.2V, pin 30 = 2.2V
Input signal level Int = – 31.5dBV
Ext = – 38.5dBV
Sub = – 33.5dBV (1kHz)
Monitoring pins: 17 and 32
∗ 1 JIS–A filter used
∗ 2 400Hz to 30kHz filter used
Parameter
Current dissipation
Voltage gain 1
Voltage gain 2
Voltage gain 3
Voltage gain 4
Distortion 1
Distortion 2
Distortion 3
Maximum output
Output noise voltage 1 (EXT)
Symbol
IqE
GVE
GVIH
GVIM
GVIL
THDW
THDE
THDZ
VOM
VONE
Min.
—
27.0
21.5
18.5
16.5
—
—
—
0.75
—
Output noise voltage 2 (INT, WIDE) VONW —
Output noise voltage 3 (INT, ZOOM) VONZ
—
Typ.
8.5
28.0
24.5
21.5
18.5
0.05
0.1
0.15
0.95
30
30
60
Max.
12.0
29.0
27.5
24.5
21.5
0.5
0.25
0.5
—
60
Unit
mA
dB
dB
dB
dB
%
%
%
Vrms
µVrms
60 µVrms
120 µVrms
Conditions
INT / EXT MIC IN, No input
EXT MIC IN
INT MIC IN, GAIN CTL H
INT MIC IN, GAIN CTL M
INT MIC IN, GAIN CTL L
INT MIC IN, WIDE, Vo = 300mVrms
EXT MIC IN, VO = 300mVrms
INT MIC IN, ZOOM, VO = 300mVrms
INT / EXT MIC IN, THD = 1%∗2
EXT MIC IN, Rg = 1kΩ∗1
INT MIC IN, Rg = 1kΩ∗1
GAIN CTL H
INT MIC IN, Rg = 1kΩ∗1
Pins 29 and 30 = 0V, GAIN CTL H
Input switch crosstalk (INT to EXT)
CTIE
— – 76 – 70 dB Note 1
Interchannel crosstalk
CTCH — – 76 – 70 dB Note 2
GC OUT L / R gain differential
GVGLR – 1.5 0.0 1.5 dB INT MIC IN, HML,10 39
Inverter OUT L / R gain differential GVILR – 1.5 0.0 1.5 dB INT MIC IN, HML, 9 40
Internal microphone power supply output voltage VREG 2.3 2.5 2.75 V Pins 4 and 45 output current for 30kΩ load
External power supply output voltage VEXT 4.3 4.5 —
V Pin 25 DC for pin 25 output current of 25mA
External power supply limit current
ILTD
— — 30 mA Pin 25 output current when grounded
VHSWH
1.6
—
VCC
V
“H” level, pin 6 / 43 DC
Input switching CTL holding voltage
VHSWL
0
— 0.7 V “L” level, pin 6 / 43 DC
VHGH
2.8
—
VCC
V
“H” level, pin 26 DC
Gain switching CTL holding voltage VHGM 1.3
—
2.0
V
“M” level, pin 26 DC
VHGL
0
— 0.5 V “L” level, pin 26 DC
HPF, CTL holding voltage
VHHPFH 2.0
—
VCC
V
HPF OFF, 19pin DC
VHHPFL
0
— 0.5 V HPF ON, 19pin DC
MIX 1 gain
GVM1-1 – 7.0 – 6.0 – 5.0 dB 63→62 / 50→62 pin
GVM1-2 – 1.0
0
1.0 dB Gain differential for pins 63 to 62 and 50 to 62
MIX 2 gain
GVM2-1 6.0 7.0 8.0 dB INT L / M / H, 2→57, 47→57pin
GVM2-2 – 1.0
0
1.0 dB Gain differential for pins 2 to 57 and 47 to 57
5
Share Link: 