OPB762 データシートの表示（PDF） - TT Electronics.
部品番号
コンポーネント説明
メーカー
OPB762 Datasheet PDF : 7 Pages
| |||
Photologic® Reflective Object
Sensor
OPB760, OPB761, OPB762, OPB763 (Series N and T)
OPB770, OPB771, OPB772, OPB773 (Series NZ and TZ)
Electrical Specifications
Electrical Characteristics (TA = 25°C unless otherwise noted)
SYMBOL
PARAMETER
Output Photologic® Sensor (continued)
IF(+)
IF(+)/IF(-)
IOS
LED Positive-Going Threshold Current(2)
Hysteresis(2)
Short Circuit Output Current:
Buffered Totem-Pole Output(1)
Inverted Totem-Pole Output(1)
Low Level Output Voltage:
Buffered Totem-Pole Output(1)(4)
VOL
Buffered Open-Collector Output(1)(4)
Inverted Totem-Pole Output
Inverted Open-Collector Output(1)(4)
High Level Output Voltage:
Buffered Totem-Pole Output(1)
VOH
Inverted Totem-Pole Output(1)(4)
Inverted Totem-Pole Output (3)
Inverted Open-Collector Output(3)
MIN TYP MAX UNITS
TEST CONDITIONS
-
- 25 mA Vcc = 5 V, TA = 25° C
1.1 - 2.0
- Vcc = 5 V
-15 - -100 mA If = 25 mA, Vcc = 5.25 V, Output = GRD
-15 - -100 mA If = 0 mA, Vcc = 5.25 V, Output = GRD
-
- 0.4
-
- 0.4
-
- 0.4
-
- 0.4
2.4 -
-
2.4 -
-
2.4 -
-
2.4 -
-
V VCC = 4.5 V, IOL = 12.8 mA, IF = 0 mA or IF =
V 30 mA
V
V
VCC = 4.5 V, IOL = 12.8 mA, IF = 25 mA
V VCC = 4.5 V, IOH = -800 μA, IF = 25 mA
V VCC = 4.5 V, IOH = -800 μA, IF = 0 mA
V
V
VCC = 4.5 V, IOH = -800 μA, IF = 30 mA
Notes:
(1) Tested at d = 0.080” (mm) from a 90% diffuse white test surface.
(2) Tested at d = 0.080” (mm), 0.150” (mm) and 0.220” (mm) from a 90% diffuse white test surface. Reference: Eastman Kodak,
Catalog #E 152 7795.
(3) Tested at d = 0.080” (mm), 0.150” (mm) and 0.220” (mm) from a 5% diffuse black test surface.
(4) Normal application would be with light source blocked, simulated by IF=0 mA.
(5) OPB760N through OPB763N series devices are terminated with 0.20” (mm) square leads designed for printed PCBoard mounting.
(6) OPB770NZ through OPB773NZ series devices are terminated with 12 inches (mm) of 7-strand 26 AWG UL1429 insulated wire on
each terminal. A standard AMP No. 640442-5 connector has been attached to the lead wires to ease connection to wire
harnesses.
(7) OPB760T through OPB763T series devices are terminated with 0.020” (mm) square leads designed for printed PCBoard
mounting.
(8) OPB770TZ through OPB773TZ series are terminated with 12” (mm) of 7-strand 26 AWG UL1429 insulated wire on each terminal.
A standard AMP No. 640442-5 connector has been attached to the lead wires to ease connection to wire harnesses.
(9) All parameters tested using pulse technique.
General Note
TT Electronics reserves the right to make changes in product specification without
notice or liability. All information is subject to TT Electronics’ own data and is
considered accurate at time of going to print.
© TT electronics plc
OPTEK Technology, Inc.
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
www.optekinc.com | www.ttelectronics.com
Issue C 05/2016 Page 5
Share Link: 