®
®
ABSOLUTE MAXIMUM RATINGS
PARAMETERS
LIMITS
+15V Supply, Pin 16
–15V Supply, Pin 19
+5V Supply, Pin 24
Digital Inputs, Pins 1, 2, 3
Analog Inputs, Pins 4-11
Lead Temperature (10s)
Short Circuit to Ground , Pin 13
0 to +18V
0 to –18V
–0.5 to +7V
–0.3 to +5.5V
–15 to +15V
300°C
Continuous
FUNCTIONAL SPECIFICATIONS
(Apply over the operating temperature range and over the operating power supply
range unless otherwise specified.)
INPUTS
MIN. TYP. MAX. UNITS
Input Voltage Range
Digital Input, Logic Levels
Logic 1
Logic 0
Logic Loading
Logic 1
Logic 0
±10
±10.5
—
Volts
+2.0
—
—
Volts
—
—
+0.8
Volts
—
—
+10
µA
—
—
–10
µA
OUTPUTS
Output Range
Output Current
Stable Capacitive Load
Output Impedance DC
±10.0 ±10.5
—
Volts
±15
—
—
mA
100
—
—
pF
—
0.1
—
Ohms
PERFORMANCE
Gain
—
–1
—
V/V
Gain Error, 25°C
—
—
±0.03 %FS
Gain Tempco
–55 to +125°C
—
±0.5
±5
ppm/°C
Offset, 25°C
—
±0.1
±0.5
mV
Offset Voltage Drift
—
<5
±15
µV/°C
Slew Rate
±250
±300
—
V/µs
Cross Talk
100kHz
—
–90
–83
dB
1MHz
—
–80
–75
dB
Bandwidth
3dB Small Signal
8
8.5
—
MHz
Full Power
3
4.5
—
MHz
Input Impedance
2.45
2.5
2.55
kΩ
Output Settling Time
(10V step, +25°C) 500Ω Load
±0.1% 10 Bits
—
100
170
ns
±0.01% 12 Bits
—
150
225
ns
±0.003% 14 Bits
—
300
400
ns
(20V step, + 25°C) 1kΩ Load
±0.1% 10 Bits
—
150
200
ns
±0.01% 12 Bits
—
200
300
ns
±0.003% 14 Bits
—
600
720
ns
Switching Characteristics
Break-Before-Make Delay
8
15
25
ns
Turn On Time
—
20
50
ns
Turn Off Time
—
20
50
ns
Harmonic Distortion
DC to 500kHz, 10Vp-p
—
–90
–80
dB
Signal-to-Noise Ratio
With Distortion
—
72
69
dB
Without Distortion
—
80
75
dB
MX-826
POWER REQUIREMENTS MIN
TYP MAX UNITS
Range
+15V Supply
+14.5
+15
+15.5
Volts
–15V Supply
–14.5
–15
–15.5
Volts
+5V Supply
+4.75
+5
+5.25
Volts
Current (Quiescent)
+15V Supply
—
+13
+21
mA
–15V Supply
—
–13
–21
mA
+5V Supply
—
<1
+1
mA
Power Supply Rejection Ratio
86
—
—
dB
Power Dissipation
—
395
575
mW
PHYSICAL/ENVIRONMMENTAL
Operating Temp. Range, Case
MC Model
MM Model
Storage Temp. Range
Package Type
Weight
0
—
+70
°C
–55
—
+125
°C
–65
—
+150
°C
24-pin, metal-sealed, ceramic DDIP
0.42 oz. (12 grams)
TECHNICAL NOTES
1. Bypass the ±15V and +5V power supplies with a 1µF, 25V
tantalum electrolytic capacitors in parallel with a 0.1µF
ceramic capacitors.
2. Analog signals up to ±15V may be present while the MUX
power supplies are off.
3. The absence of an RON specification or output leakage
specification is related to the architecture of the switching
network. The inputs see a constant 2.5k Ohm input
impedance whether the channel is on or off.
4. Typical recovery time from an overvoltage condition of >±3V
is approximately 200 nanoseconds from a negative
overdrive and 700 nanoseconds from a positive overdrive.
5. Double-level multiplexing may be used to provide up to 64
channels (nine MX-826’s required).
Table 1. Channel Addressing
On
Channel
1
2
3
4
5
6
7
8
MUX Address
A2 A1 A0
0
0
0
0
0
1
0
1
0
0
1
1
1
0
0
1
0
1
1
1
0
1
1
1