GL603USB データシートの表示（PDF） - Genesys Logic

部品番号

コンポーネント説明

メーカー

GL603USB

USB + PS/2 MOUSE MICROCONTROLLER

Genesys Logic 

GL603USB/GL603USB-A/GL603USB-B

06h

PORT1

Port 1 data register

07h

PORT2

Port 2 data register

0Ah

PCHBUF

Write buffer of Program Counter’s bit 10-8

0Bh

INTEN

Interrupt enable register

0Dh

PHVAL

Photo-sensor value register

0Eh

PHSEL

Photo-sensor input select register

0Fh

DMODE

Photo-sensor input mode register

80h

INDR

Addressing this location will use the content of INDAR to address data

memory (not a physical address)

81h

PSCON

Prescaler control register

82h

PCL

Program Counter’s low byte

83h

STATUS

Status register

84h

INDAR

Indirect address register

86h

PORT1CON

Port 1 direction control register

87h

PORT2CON

Port 2 direction control register

8Ah

PCHBUF

Write buffer of Program Counter’s bit 10-8

8Bh

INTEN

Interrupt enable register

Table 4-2 MCU Function Register Summary

INDR (Address 00h/80h)

INDR is not a physical register. Addressing INDR register will cause indirect addressing. Any instruction

using the INDF register actually accesses the register pointed by the INDAR register.The indirect

addressing method only can be used for general purpose registers.

TIMER (Address 01h, Timer register)

R/W

R/W

R/W

R/W

R/W

R/W

R/W

R/W

TIMER7 TIMER6 TIMER5 TIMER4 TIMER3 TIMER2 TIMER1 TIMER0

The timer starts to count up after power on reset. The TMROF bit at INTEN register will be set when the

TIMER register overflows from FFh to 00h. If both TMROEN and GIE bits at INTEN register are set, an

interrupt will be generated when TIMER register overflows.

Value on POR: “0 0 0 0 0 0 0 0”

PCL (Address 02h/82h, Program Counter’s low byte)

R/W

R/W

R/W

R/W

PCL7

PCL6

PCL5

PCL4

R/W

PCL3

R/W

PCL2

R/W

PCL1

R/W

PCL0

The Program Counter (PC) is 11-bit wide. The low byte comes from the PCL register, which is a readable

and writable register. The high byte is not directly readable or writable and comes from PCHBUF. The

GL603USB has a 4 level deep x 11-bit wide hardware stake. The stake space is not part of either program

or data space and the stack pointer is not readable or writable. The PC is pushed onto the stack when a

CALL instruction is executed or an interrupt causes a branch. The stack is poped in the event of a RETIA,

RETI or a RET instruction execution. PCHBUF is not affected by a push or pop operation.

When write to PCL command executed, all 3 bits of PCHBUF will be loaded to PC because PCL is only a

8 bits register.

Value on POR: “0 0 0 0 0 0 0 0”

Status (Address 03h, Status register)

R/W

R/W

R/W

R/W

BS

ZO

HC

CA

BS: Bank Select. Because only 7 bits (bit 0~bit 6) operand implied by instruction for register address, this

bit is used as address bit 7 when register access.

1: Bank 1 (80h-FFh)

17

09/22/00

Revision 1.4

Share Link: