M58MR016C データシートの表示（PDF） - STMicroelectronics

部品番号

コンポーネント説明

メーカー

M58MR016C

16 Mbit (1Mb x16, Mux I/O, Dual Bank, Burst) 1.8V Supply Flash Memory

STMicroelectronics 

M58MR016C, M58MR016D

duces active current consumption. Program is

aborted if RP turns to VIL.

If a Program Suspend instruction was previously

executed, the Program operation may be resumed

by issuing the command D0h using an address

within the suspended bank (see Table 11). The

status register bit b2 and bit b7 are cleared when

program resumes and read operations output the

status register after the erase is resumed (see Ta-

ble 12). The suggested flowchart for program sus-

pend/resume features of the memory is shown

from Figure 18.

Block Protect (BP)

The BP instruction use two write cycles. The first

command written is the protection set-up 60h. The

second command is block Protect command 01h,

written to an address within the block to be protect-

ed (see Table 11). If the second command is not

recognized by the C.I the bit 4 and bit 5 of the sta-

tus register will be set to indicate a wrong se-

quence of commands (see Table 12). To read the

status register write the RSR command.

Block Unprotect (BU)

The instruction use two write cycles. The first com-

mand written is the protection set-up 60h. The sec-

ond command is block Unprotect command D0h,

written to an address within the block to be protect-

ed (see Table 11). If the second command is not

recognized by the C.I the bit 4 and bit 5 of the sta-

tus register will be set to indicate a wrong se-

quence of commands (see Table 12). To read the

status register write the RSR command.

Block Lock (BL)

The instruction use two write cycles. The first com-

mand written is the protection set-up 60h. The sec-

ond command is block Lock command 2Fh,

written to an address within the block to be protect-

ed (see Table 11). If the second command is not

recognized by the C.I the bit 4 and bit 5 of the sta-

tus register will be set to indicate a wrong se-

quence of commands. To read the status register

write the RSR command (see Table 12).

BLOCK PROTECTION

The M58MR016C/M58MR016D provide a flexible

protection of all the memory providing the protec-

tion, un-protection and locking of any blocks. All

blocks are protected at power-up. Each block of

the array has two levels of protection against pro-

gramming or erasing operation. The first level is

set by the Block Protect instruction; a protected

block cannot be programmed or erased until a

Block Unprotect instruction is given for that block.

A second level of protection is set by the Block

Lock instruction, and requires the use of the WP

pin, according to the following scheme:

– when WP is at VIH, the Lock status is overridden

and all blocks can be protected or unprotected;

– when WP is at VIL, Lock status is enabled; the

locked blocks are protected, regardless of their

previous protect state, and protection status

cannot be changed. Blocks that are not locked

can still change their protection status;

– the lock status is cleared for all blocks at power

up.

The protection and lock status can be monitored

for each block using the Read Electronic Signature

(RSIG) instruction. Protected blocks will output a

'1' on DQ0 and locked blocks will output a '1' in

DQ1 (see Table 13).

PROTECTION REGISTER PROGRAM (PRP)

and LOCK PROTECTION REGISTER

PROGRAM (LPRP)

The M58MR016C/M58MR016D features a 128-bit

protection register and a security Block in order to

increase the protection of a system design. The

Protection Register is divided in two 64-bit seg-

ments. The first segment (81h to 84h) is a unique

device number, while the second one (85h to 88h)

can be programmed by the user. When shipped

the user programmable segment is read at '1'. It

can be only programmed at '0'.

The user programmable segment can be protect-

ed writing the bit 1 of the Protection Lock register

(80h). The bit 1 protects also the bit 2 of the Pro-

tection Lock Register.

The M58MR016C/M58MR016D feature a security

Block. The security Block is located at 0FF000-

0FFFFF (M58MR016C) or at 000000-000FFF

(M58MR016D) of the device. This block can be

permanently protected by the user programming

the bit 2 of the Protection Lock Register (see Fig-

ure 5).

The protection Register and the Protection Lock

Register can be read using the RSIG and RCFI in-

structions. A subsequent read in the address start-

ing from 80h to 88h, the user will retrieve

respectively the Protection Lock register, the

unique device number segment and the OTP user

programmable register segment (see Table 23).

WRITE READ CONFIGURATION REGISTER

(CR).

This instruction uses two Coded Cycles, the first

write cycle is the write Read Configuration Regis-

ter set-up 60h, the second write cycle is write

Read Configuration Register confirm 03h both to

Read Configuration Register address (see Table

11).

This instruction writes the contents of address bits

ADQ15-ADQ0 to bits CR15-CR0 of the Read Con-

17/51

Share Link: