MACH4-96 データシートの表示（PDF） - Lattice Semiconductor

部品番号

コンポーネント説明

メーカー

MACH4-96

High-Performance EE CMOS Programmable Logic

Lattice Semiconductor 

ABSOLUTE MAXIMUM RATINGS

Storage Temperature . . . . . . . . . . . . . .-65°C to +150°C

Ambient Temperature

with Power Applied . . . . . . . . . . . . . .-55°C to +125°C

Device Junction Temperature . . . . . . . . . . . . . +150°C

Supply Voltage with

Respect to Ground . . . . . . . . . . . . . . -0.5 V to +7.0 V

DC Input Voltage . . . . . . . . . . . . -0.5 V to VCC +0.5 V

DC Output or

I/O Pin Voltage . . . . . . . . . . . . . . -0.5 V to VCC +0.5 V

Static Discharge Voltage . . . . . . . . . . . . . . . . . 2001 V

Latchup Current

(TA = –40°C to +85°C) . . . . . . . . . . . . . . . . . . . 200 mA

Stresses above those listed under Absolute Maximum Ratings

may cause permanent device failure. Functionality at or above

these limits is not implied. Exposure to Absolute Maximum

Ratings for extended periods may affect device reliability.

VANTIS

OPERATING RANGES

Industrial (I) Devices

Temperature (TA) Operating

in Free Air . . . . . . . . . . . . . . . . . . . . . . –40°C to +85°C

Supply Voltage (VCC) with

Respect to Ground. . . . . . . . . . . . . +4.50 V to +5.50 V

Operating ranges define those limits between which the

functionality of the device is guaranteed.

DC CHARACTERISTICS over COMMERCIAL operating ranges

Parameter

Symbol

Parameter Description

Test Conditions

Min Typ Max Unit

VOH

Output HIGH Voltage

VOL

Output LOW Voltage

VIH

Input HIGH Voltage

IOH = -3.2 mA, VCC = Min

VIN = VIH or VIL

IOL = 24 mA, VCC = Min

VIN = VIH or VIL (Note 1)

Guaranteed Input Logical HIGH

Voltage for all Inputs (Note 2)

2.4

V

0.5 V

2.0

V

VIL

Input LOW Voltage

Guaranteed Input Logical LOW Voltage for all

Inputs (Note 2)

0.8 V

IIH

Input HIGH Leakage

Current

VIN = 5.25 V, VCC = Max (Note 3)

10 µA

IIL

IOZH

IOZL

ISC

Input LOW Leakage

Current

Off-State Output Leakage

Current HIGH

Off-State Output Leakage

Current LOW

Output Short-Circuit

Current

VIN = 0 V, VCC = Max (Note 3)

VOUT = 5.25 V, VCC = Max

VIN = VIH or VIL (Note 3)

VOUT = 0 V, VCC = Max

VIN = VIH or VIL (Note 3)

VOUT = 0.5 V, VCC = Max

(Note 4)

-100 µA

10 µA

-100 µA

-30

-160 mA

ICC

Supply Current

VIN = 0 V, Outputs Open

(IOUT = 0 mA), VCC = 5.0 V,

f =25 MHz, TA = 25°C (Note 5)

225

mA

Notes:

1. Total IOL for one PAL block should not exceed 128 mA.

2. These are absolute values with respect to device ground and all overshoots due to system or tester noise are included.

3. I/O pin leakage is the worst case of IIL and IOZL (or IIH and IOZH).

4. Not more than one output should be shorted at a time and duration of the short-circuit should not exceed one second.

VOUT = 0.5 V has been chosen to avoid test problems caused by tester ground degradation.

5. Measured with a 16-bit up/down counter pattern. This pattern is programmed in each PAL block and capable of being loaded,

enabled, and reset. An actual ICC value can be calculated by using the “Typical Dynamic ICC Characteristics” Chart towards the

end of this data sheet.

MACH4-96/96-18 (Ind)

17

Share Link: